Models > SGR231HS0 > Instructions

SGR231HS0 Westinghouse Dryer - Instructions

All installation instructions for SGR231HS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SGR231HS0
16-30 of 320
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drum would not turn

  • Customer: jeana from houston TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 13 of 15 people found this instruction helpful
remove the rear lower left vent cover to get access the belt tensioner and pulley. then pop the top section up with a flathead screwdriver in the front, freeing it from the popclips. Then remove two screws from the back side of the front section releasing the drum. loop the belt around the drum.

Motor shaft broke

  • Customer: Beverly from Blairsville GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 12 of 14 people found this instruction helpful
had to remove the belt and drum and then remove the motor and replace it...put the belt on and then the hard part was to get the drum in place without the belt coming off. New Motor works quieter than the old one did, so I assume the dryer came with a defective motor to begin with and then the shaft finally broke. It runs very quiet now, but never did before. Even a service man came when it was new but said that was normal. Now we know it was not....there was a problem from the start.

lint filter did not fit "squarely" into its place

  • Customer: Jeff from Bethalto IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 11 people found this instruction helpful
replaced old filter, only to find that the new one had the same issue. After closer examination, I determined the filter guide that screws into place, which I had removed earlier to clean lint out, did not hold the lint casing correctly. I removed and reinstalled the piece that has the metal moisture sensors, and replaced it, ensure both screws held the lint casing as it should. Now I have two lint filters that fit perfectly! So, if you ever remove the piece wtih the metal sensors, make sure that the lint casing is screwed in correctly when replacing.

DOOR LATCH & DOOR STRIKE BROKEN ON DRYER

  • Customer: Bruce from Seminole FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 13 of 18 people found this instruction helpful
I REMOVED THE BROKEN DOOR LATCH & STRIKE WITH PLIERS. THEN I PUSHED THE NEW PARTS INTO PLACE

Dryer was missing the grounding ball and making a loud squeal

  • Customer: Jason from Bellevue IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 12 of 17 people found this instruction helpful
First I located the two clips holding the top of the machine on and opened the top of the dryer. I then disconnected the two wires on the door switch and removed the two screws holding the front panel on. After removing the front panel, I vacuumed all the loose lint and as far into the lint trap as possible. I then removed the back vent panel and released the drum belt from the pulley. I pulled the drum out of the support bearing. Then I removed two screws holding the drum support bearing, bracket, and grounding ball clip. I replaced the grounding ball and drum support bearing with new parts, (as the drum support bearing was damaged without the grounding ball). Then I reversed the order and put the dryer back together. Overall I felt the job was easy and I'm happy to be able to use a quiet machine again!!!

Drum making thumping noises, clothes getting caught behind drum.

  • Customer: Gerald from Baltimore MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 9 of 9 people found this instruction helpful
I've always been a "do it yourselfer". If I can fix it, I save money. I took the dryer apart by lifting the top up like car hood. Then I removed the front panel. The front drum glide snapped into place easily where the other one had broken off. The felt strip that you sent was much shorter than the one on the dryer, so once I used the wire wheel to remove the old glue, I cut off the section of the felt that was bad and replaced it with the new felt. The turns much quieter and clothing doesnt get caught behind the drum anymore.

the burner wouldn't ignite

  • Customer: Michael from Newbury Park CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 8 people found this instruction helpful
UNPLUG the appliance. After removing the top of the dryer the front is easily removed. To make life simple I disconnected the wire harrness at the quick disconnect and placed the door/front away from the workspace. I removed the bracket holding the coils in place and replaced the old with the new coils. replaced the front and top panels and pugged it in! Good as new!! I originally ordered the wrong part and PART'S SELCET.COM refunded my money no problem! I will bookmark this site and use it again.

My husband ruined the old latch by trying to shut the door too hard, and the old latch fell down into the inside of the dryer.

  • Customer: Michelle from Dallas TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 12 people found this instruction helpful
I took the new latch out of the package and snapped it into place. It took about 15 seconds, and that included the walk to the laundry room!

switch burnt out

  • Customer: paul from west keansburg NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 7 people found this instruction helpful
first you had to take back top panel off remove wires from switch turn old switch to the right pull it out then connect wires to new switch put switch back in screw back panel back on very easy 10 minutes tops thank you

The dryer drum wouldnt turn

  • Customer: Kara from Beckly WV
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 8 of 11 people found this instruction helpful
Had to pretty much disassemble the entire dryer. The schematics on the web site made it a snap to do. One word of advice. I you have to replace the rear drum assembly, the drum has to come out the front of the dryer. Part select made this a very positive experience.

i broke the knobs and couldn't find the parts t the local hardware store.

  • Customer: Ricardo from pomona CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 9 people found this instruction helpful
I popped the knobs on without tools. Easy! I saved $36.00 buying directly from you instead of my local repair man

dryer drum squealing loudly!

  • Customer: john from waynesboro VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 6 of 6 people found this instruction helpful
THIS UNIT IS A STACKABLE WASHER&DRYER,SO FIRST PULL UNIT AWAY FROM WALL ATLEAST 4 FOOT.UNPLUG POWER CORD,THEN TAKE10 DAGREE FRONT PANEL OFF THEN THE CONTROL PANEL OFF AND UNPLUG THE 5 CONNETORS IF YOUR UNIT HAS THAT MANY,THEN LAY PANEL ASSIDE.TAKE DRYER DOOR OFF,MAKES IT EASIER WHEN PUTTING IT ALL BACK TOGETHER.NOW TAKE FRONT PANEL OFF AND THE DRYER LENT TUBE,NOW JUST TAKE THE 3 CENTER PHILLIPS HEAD SCREWS OUT AND SLIDE DRUM OUT.PULL UPWARD ON WHAT THEY CALL THE SHAFT WHICH HELD DRUM ON.NOW THESE ARE THE PARTS YOU SHOULD ORDER.BELT,GROUNDING BALL CLIP,GROUNDING BALL,DRUM SUPPORT BEARING,BEARING BRACKET,AND MOST IMPORTANT PART IS THE SHAFT.THE SHAFT IS UR INSURANCE FOR THE WHOLE JOB.USE A GOOD GREASE LIKE WHITE LITHIUM GREASE AND COAT THE SHAFT END AND THE DRUM SUPPORT BEARING.THE GREASE WILL CUT DOWN ON FRICTION FOR A WHILE,AND RE ASSEMBLE THE WAY YOU TOOK APART.REMINDER GROUNDING BALL GOES BEHIND DRUM SUPPORT BEARING NOT IN FRONT.GOOD LUCK AND PLEASE VACCUM.

Wretched screeching noise

  • Customer: Paul from Broadalbin NY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 6 people found this instruction helpful
Make sure you order a new belt and a new drum glide with the rear drum bearing assembly. If your bearing is worn out, so are the belt and drum glide!

1) Use a flat screw driver or putty knife to release the blind clips that hold the front side of the top of the dryer cabinet down
2) Swing dryer top up and remove two screws that hold the face of the cabinet.
3) Unplug the wiring harness and remove the cabinet face.
4) Remove the 3 screws that hold the drum to the bearing assembly (accessed from inside the drum. This makes it easier to remove the drum as the bearing assembly can be difficult to remove before you see how it snaps together
5) Reach under the drum and take the belt off the motor pulley, then remove the drum
6) Remove the old bearing assembly from the socket (slide up then out)
7) Remove the two screws that hold the bearing socket to the dryer
8) Fasten the new socket to the dryer (you'll need help doing this unless you have REALLY long arms because you have to reach inside the driver and the back of the dryer at the same time)
9) Grease the socket with the supplied high temp grease
10) Bolt the new bearing assembly to the drum and put the new belt around the drum
11) Put the drum back in and snap the bearing socket in and down
12) Guide the new belt around the motor pulley & tensioner
13) Glue the new drum glide / felt piece to the front cabinet
14) Put the cabinet back together

cloths getting caught along drum glide and lint trap and black streaks/sometimes tearing

  • Customer: Gabriellle from Vancouver WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
1) pulled Dryer out from wall and removed top panel

No heat/intermittent heat. Ignitor glowed but no gas flame.

  • Customer: Jeffrey from Richmond TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
White Westinghouse WDG547PB Dryer. Removed access panel (lower left front of dryer) by removing phillips head screw below access panel. Removed two phillips head screws holding bracket that holds coil in place. Removed coil, disconnected electrical connector. Connected electrical connector to new coil and set in place. Repeat for second coil. Reinstall bracket and access panel. Job complete. Dryer back in service with no problems.
All Instructions for the SGR231HS0
16-30 of 320