Models > SGC355XX3

SGC355XX3 Roper Range - Overview

Get Parts and Repair Help for SGC355XX3

If you know the range repair part you need, you can browse the list of all parts on the SGC355XX3, or you can search by name or part description. You can also find your part by where it is located on the SGC355XX3 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for SGC355XX3 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.58

Light Bulb - 40W

Sold individually.

Order within the next 5 hrs and your part ships today!
$2.70

Cover Screw

Sold individually.

Order within the next 5 hrs and your part ships today!
$2.70

Screw

This screw is sold individually.

Order within the next 5 hrs and your part ships today!
$18.07

2 Piece Broiler Pan

The top of this part is now black.

Order within the next 5 hrs and your part ships today!
$28.02

Suface Burner Ignition Switch

When the gas burner valve knob is depressed and turned, this part creates a spark that lights the gas and starts the burner.

Order within the next 5 hrs and your part ships today!
$27.77

Rocker Switch - Black

This rocker switch can be used for both the oven selector and/or the oven light.

Order within the next 5 hrs and your part ships today!
$4.13

Thermostat Bulb Clip

Order within the next 5 hrs and your part ships today!
$4.05

Screw - #10 - 32x1/2

Sold Individually.

Order within the next 5 hrs and your part ships today!
$2.70

Screw

This screw is sold individually.

Order within the next 5 hrs and your part ships today!
$4.05

SCREW

Order within the next 5 hrs and your part ships today!

Common Symptoms of the SGC355XX3 [Viewing 1 of 1]

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven seals got dried and cracked

  • Customer: Brent from Goleta CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 15 of 20 people found this instruction helpful
The top seal was too long (my fault, ordered wrong length seal) so I had to cut it and high-temp epoxy the metal hook into the end. Overall pretty easy fix. read more

Ignitor did not spark when turning the know

  • Customer: Richard from Lansing MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
Had to remove the 4 range knobs, and the oven knob and then the facie. Two screws under the end caps and two on each side from the back on each end. Design defect: one of these screws which attaches through the frame to the facie also attaches the support which holds up the range top. Take that one off last. Remove the two wires that attach to the oven light... read more

Left rear burner would not ignite

  • Customer: John from Perth Amboy NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
Removed the burner plates. Lifted up the range top. Removed the knobs. Unbolted the 2 rounded nuts at top of face plate. Removed the 4 screws that hold the face plate in place from behind. Un plugged the old switch and plugged in the new one and bam! The burner worked. Thanks, Super fast shipping! The part was here in less than 36 hours. John, N.J. read more