Models > SF315PEKW0 > Instructions

SF315PEKW0 Whirlpool Range - Instructions

All installation instructions for SF315PEKW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SF315PEKW0
1-15 of 53
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

F3 Error message

  • Customer: Charles from Brecksville OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 69 of 88 people found this instruction helpful
Two screws remove the front of the sensor (put a pan under the sensor to catch the screws), One nut removes the rear cover to access the rear of the sensor. Separating the two halves of wiring harness takes a little dexterity. BIG TIP! Tie a string to the back of the sensor wire and pull the sensor out from the front making sure the string still shows thru the back. If you don't you have a 15 minute job trying to fish the wires at an angle thru the insulation (a very frustrating task). Untie the string from the old and tie it securely to the new. Pull the string from the back and Voila! your new sensor can be plugged in or wirer nutted to the old connection on the back of the stove. Replace the nut and the two screws and you're done!

our oven would not heat up

  • Customer: sharnette from baltimore MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 24 of 27 people found this instruction helpful
My husband pulled out the stove turned the gas off then he pulled out the part and replaced igniter....it took only about 20 min to do this job it was very easy and prior to us doing ourselves i called a well known company that does home repairs, I also called a few smaller businesses and to replace this part was anywhere from $175- 250 if not more. we are very very happy with our decision to replace the part ourselves unstead of spending extra money we didnt have .

Oven would not heat.

  • Customer: Nedra from Alsip IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 12 of 14 people found this instruction helpful
Installing the part was really easy. I first turned the gas off, simply remove two screws tht hold the igniter in place. I then remove four screws from the back panel and disconnected the part. The feedback from other users on your site made me realize how easy it was. It took less than thirty minutes.

The igniter would turn orange but wouldn't fire up, so the oven wouldn't heat up.

  • Customer: Lisa from Livermore CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 10 people found this instruction helpful
I just unscrewed the old one out, which was 2 screws and screwed this one in. But the thing that was best of all was how fast the part came in. It literally came the next day.

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 9 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Oven would not heat

  • Customer: sean from san bernardino CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench(Adjustable)
  • 6 of 8 people found this instruction helpful
Amazing after two years off frustration due to unsurety of problem went to your site found part problem in question that matched my problem.two screws and a plug now im burning like im supposed to.success

Igniter glowed but oven would not light

  • Customer: Kenneth from Garden Valley CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
We looked up the trouble shooting page on PartsSelect and ordered the part recommended. Part arrived very quickly. Simple installation, two screws and plug in. Problem fixed.

Ignitor would glow but not power gas valve

  • Customer: Jacquelyn from Billerica MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 8 people found this instruction helpful
New ignitor fixed the problem

No heat in the Broiler/oven.

  • Customer: Matthew from Reno NV
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 6 of 9 people found this instruction helpful
Removed the panels, disconnected and dismounted the igniter and installed the new one. Pretty simple.

oven wouldn't light

  • Customer: Herman from Gallitzin PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 5 of 6 people found this instruction helpful
shut off gas supply,removed gas lines at gas valve ,marked where wires went,replaced gas valve,worked well.

Replacing the bulb in the freezer side

  • Customer: Yafa (and David) from Bothell WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 5 people found this instruction helpful
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

oven wouldn't lite

  • Customer: Herman from Gallitzin PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set, Wrench(Adjustable)
  • 3 of 3 people found this instruction helpful
Removed two lines ,two wires,and two screws, then reversed and i was done.

oven light burnt out

  • Customer: William from Schwenksville PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Broken Door Handle and Holding Trim

  • Customer: STACI from LOS ANGELES CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
The repair was/is a simple process only I didn't have all the parts. I assumed for the $12 price that I would be getting a PAIR of the very small door trims but there was only one so I had to order yet another to finish the job... It required 2 people, one to hold the glass door while being attached but overall it was a very easy fix.

Handle broke on Range Door

  • Customer: Nancy from Leander TX
  • Difficulty: Very Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 7 of 19 people found this instruction helpful
Handle was not able to install easily; tried to hammer rivet to secure new handle to door & broke glass panel...now have to buy a new stove because this one has been discontinued.
All Instructions for the SF315PEKW0
1-15 of 53