SER341AS0 Westinghouse Dryer - Instructions

Unplug dryer (gotta say it). Remove the two screws that hold in the lint catch. Remove top of dryer (two screws in back hold brackets, the front snaps on). remove two screws along the front edge to take front panel off the dryer (there are also clips). Unhook the two electrical connectors that control the door shut off. Once the front is off, remove the old glide and felt and install the new parts. Be sure not to step on the tube of contact cement, making it explode inside the bag. That sucked. Reassemble.

Had to pretty much disassemble the entire dryer. The schematics on the web site made it a snap to do. One word of advice. I you have to replace the rear drum assembly, the drum has to come out the front of the dryer. Part select made this a very positive experience.

Make sure you order a new belt and a new drum glide with the rear drum bearing assembly. If your bearing is worn out, so are the belt and drum glide!

1) Use a flat screw driver or putty knife to release the blind clips that hold the front side of the top of the dryer cabinet down
2) Swing dryer top up and remove two screws that hold the face of the cabinet.
3) Unplug the wiring harness and remove the cabinet face.
4) Remove the 3 screws that hold the drum to the bearing assembly (accessed from inside the drum. This makes it easier to remove the drum as the bearing assembly can be difficult to remove before you see how it snaps together
5) Reach under the drum and take the belt off the motor pulley, then remove the drum
6) Remove the old bearing assembly from the socket (slide up then out)
7) Remove the two screws that hold the bearing socket to the dryer
8) Fasten the new socket to the dryer (you'll need help doing this unless you have REALLY long arms because you have to reach inside the driver and the back of the dryer at the same time)
9) Grease the socket with the supplied high temp grease
10) Bolt the new bearing assembly to the drum and put the new belt around the drum
11) Put the drum back in and snap the bearing socket in and down
12) Guide the new belt around the motor pulley & tensioner
13) Glue the new drum glide / felt piece to the front cabinet
14) Put the cabinet back together

The blower wheel was a bit difficult, but manigable to do yourself.

I contacted a company to come out and diagnose the problem. They informed me that the thermal limiter is bad and needed to be replaced for $15 for the part and $85 labor. I found the part on this site for about $10, and did the repair myself. The dryer was mostly dismantled so I pulled the drum back, and replaced the part. The tricky part was the pulley system was, so make sure you see it before hand or find a diagram online. Once that was figured out, I set the drum back up, greased and tightened the pulley, reattached the front of the washer with connections, and closed the lid.

The repair actually was quite easy but diagnosing the problem was another story. I found out that the dryer would not buzz and vibrate , if I just ran the fluff cycle but no heat. As soon as heat applied, the slight buzzing and slight vibrating would occur after a few minutes. I knew it wasn't the drum bearing, the drum rollers, the rubbing collar on front of drum, idle arm, belt, etc - I had replaced all of them less than a year ago. Anything I found on the internet dealing with the motor was always geared around not running or slow starting or shutting down, loud buzzing, needing a push start to start, etc but that was not the case. So I figured it was the blower housing and ordered that part. However, once I had the machine apart the blower housing seemed to be just fine - nothing obvious, everything tight. The one issue I had was removing the plastic nut with the metal insert on the blower unit that attaches it to the motor shaft which just wouldn't bulge. So I said to myself, the h*ll with it, lets get a new motor, too and remove both parts together which btw, was very easy. So that is exactly what I did. Now with new motor in hand and new blower housing in hand, I easily removed the old motor still attached to the old blower housing together and replaced both which was very easy. Hooked everything back up and no more soft buzzing or slight vibration. Now back to the problem or my guess at this point. I noticed that the rubber mounting bushing in the back of the motor which is used to attached it to the dryer bracket was funking looking - kinda soft and a bit perished. So I am surmising that once heat was introduced, it was enough to soften that bushing enough to cause the slight buzzing and slight vibration but without the heat to soften the bushing a bit, it was quiet and steady. Just a guess but for anyone that has this issue with just heat but no issue with fluff (no heat) check out the condition of that rubber mounting bushing on the rear of the motor. No where on the internet was there any info concerning the symptoms I had and I was flying by the seat of my pants. So am taking the time to get this on record in case someone else has these symptoms and finds it.

Very simple to take dryer apart ,1st top snaps off and 2 screws and front comes off,Dryer needed new front guide but I replaced rear support and belt also as recommended, good time to clean it out too.Hardest part was getting old guide and lower seal off, don't know if it's right but I used a small die grinder with a wire brush attached and it went real quick to clean old felt and glue off. $85 and dryer runs like it is brand new. easy for anyone with some mechanical ability. PartsSelect webpage made getting the right parts fast and easy

Tried to follow the directions of others but ran into a problem with getting the top panel off. This is how I did it.
1 Disconnect power and dryer vent tube. Move away from wall.
2 Remove slotted access panel in back of dryer and take belt off motor and idler pulley. Leave on drum.
3 Unscrew the screws on the back of the top panel brackets( mine are silver) where they screw into the back panel and pull up and to the back to get the top panel off. Someone else said to slide a putty knife in the front to release the top but my machine has no spring clips.
4 With the cover off you can see the two heat sensors and I tested them with a multi meter they registered 0 which meant they were OK.
5 Remove the screws that hold the control board on and the plugs that are wired into it making sure that you draw a diagram to remember the wiring. There was a zip tie that I cut to be able to feed the plugs through the hole in the front panel that the wiring must go when the front panel drops down.
6 Remove the screws on the top of the front panel and the screws on the inside of the side panel that hold the front panel secure.
7 A lot goes on on step 7 because the front panel which is hinged drops from the top down to the floor. Diagram and remove all wires there are two green ground wires on the side, Three wires on the door lock, two wires for the light and wires for a moisture sensor. When disconnected feed the control panel plugs and other wires through the hole in the front panel and lift up and out on the front panel it will pop out. Lower it to the floor and let it rest there.
8 Now you can get the drum out of the way by pulling up then out the front where the front panel is now on the floor. Leave the belt on it.
9 Diagram the wiring on the heating element there are connections for the element and the sensor. They gave me a new sensor screwed onto the new heating element. Then unscrew it from the back panel the screws are on the back of the machine.
10 Install is the reverse of the rip down

In hindsight I would have liked to have had the new part before I started the project because the wiring wasn't so fresh in my head a week later when it arrived even with diagrams. Over all it was very simple and took under two hours to complete. I did clean everything I could inside the machine and reglued a couple of the seals that had fallen loose. Works like new and probably went because of overheating with a clogged vent. Lesson... clean your dryer vent every year or sooner.

I don't think it would take others as long as it took me.
I had to take the drum out to get to the limiter. And my dryer is in a builtin housing with limited space in front of the dryer - so lots of manuevers to get access.

The limiter was very easy to find, thanks to diagrams on this site. The space between drum and limiter made it impossible to get to the limiter screws without removing drum. Found very helpful drum removal instructions on PartSelect here:

http://www.partselect.com/PS1148434-Frigidaire-134503600-Dryer-Drum-Belt.htm?SourceCode=13&ModelNum=FSE748GFS0

Great site - thank you.

While changing power cable from 3 prong to 4 prong connection on a recently purchased used dryer I found the terminal block partially melted due to improper connectors which overheated. The bracket and cover were also missing which presented a shock hazard for anyone touching the exposed connections and there was no way to connect the strain relief. I disconnected the old 3 prong cable, removed the old terminal block, installed the new terminal block (required opening the dryer top for access), threaded power cable through bracket and fastened with strain relief leaving loose, attached the neutral/ground wires to middle terminal connection point, red to red wire in terminal block and black to black wire also in terminal block and tightened bracket and added cover.

my motor was making noise i tried to replace the motor but could not get the blower wheel off the motor so i had to buy a blower and housing assy. also... now it works great...

Dryer door would not close, part had broke and fallen in. Once part was received it took less than an minute to put the new one in and I was back in business.

thanks for making it easy to find the part needed. and the delivery was fast!

bonnie J.

1. Released the front latches under the dryer top and flipped it up.
2. Removed two screws holding the dryer front in place and flipped it down.
3. Tore off old drum glide and lower seal.
4. removed most of the remaining fuzz with sandpaper.
5. Glued the new seals in place.
6. Put everything back together.

All in all, about 30 minutes of effort. I managed to come away with only minor cuts and scrapes.

Much cheaper than a new dryer!

unplug dryer. lift the top of the dryer up and back. Take the screws out holding the front panel on. One on each side. Disconnect wires from door open stop switch and take front panel off. Remove drive belt from around pulleys and lift drum up and forward out the front of the dryer. I had to replace the plastic and metal holder and the grounding ball also. Remove the shaft from the drum and put he new one on. Put the drum back in, wrap the belt around the drum and set drum in plastic holder. Then just reverse your steps. Fairly easy.

Used nut driver to remove screw and cover from dryer cord terminal block, used screw driver to remove two screws securing old terminal block, cut dammaged wire and stripped wire back and crimped on new terminal connecter, replaced old terminal block with new one, replaced two screws, installed new cord, and replaced cover plate and screw.