Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SEG196W Maytag > Instructions

SEG196W Jenn-Air Range - Instructions

All installation instructions for SEG196W parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SEG196W
76-90 of 131
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

needed new grease filter

  • Customer: Mary from Anna Maria, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Removed old grease filter,replaced with new grease filter. No tools needed.
I ordered the grease filter on Tuesday and it arrived at my door on Wed.
Best experience ever ordering a part, I will definitely use Part Select again and have already recommended it to friends.

old bulb fused into old socket.

  • Customer: Michael from Reno, NV
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 7 people found this instruction helpful
removed old socket and replaced.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.

Electronic Clock Assembly quit

  • Customer: Gayle from Lenoir City, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 4 people found this instruction helpful
It was easy to get apart. I drew out a schematic of where the wires were so I could put them back in the same place. I plugged them all back up and it worked! Only problem was, there was a dead mouse behind the panel! He had not chewed anything, so the unit just went out from age.

switch broke off and fell into oven cavity

  • Customer: alfio from piedmont, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 4 people found this instruction helpful
removed two screws, pulled up hardware / components, unplugged the old switch, (remember to switch off the circuit breaker!) the two 'fasteners' that are supposed to keep the switch tied to the cover panel did not fit, so i had to use epoxy to secure the switch. no problem though.

The old switch disintegrated and I lost all functionality of fan or light

  • Customer: Chris from Everett, WA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
The part I ordered is the perfect match for this stove. Replacement was a breeze. Take the 2 screws out that hold the switch housing, using an old dental pick, I pryed out the old washers, put the new switch in, used a small socket to push the new washers on, hooked up the wires, done. Gotta love partselect.com!

Rocker Switch For Vent Fan/Oven Light.

  • Customer: William from Gordon, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 1 of 4 people found this instruction helpful
Trouble shooting: rocker switch "blew-up", fire flew when wife opened oven door. Assumed rocker switch was burned due to melted plastic and a terminal blew off. Down draft fan would not run. Put stove breaker in off position. Search on internet located "part select". Entered model number and discription. Picture of switch and simple diagram appeared on screen with part #. I ordered part, it was here 2 days later. Eating home cooked meals now. Bragging about repairing my stove, repair savings of about $150. 00.

50 year old oven racks in bad shape

  • Customer: GREG from PETALUMA, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Parts no longer available so we went to several appliance stores and measured racks. We found a jenair model had racks that measured correctly got the model number and ordered the racks. There working great and now the oven looks like new. Our kitchen is a restored 1956 GE metal kitchen in Cadilac pink. Thanks guys for the fast service and very resonsble price. Was also very happy to find the racks were made in USA.

needed new grease filter

  • Customer: Barbara from Hubert, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
It was hard. I simply replaced the old one!! fIT PERFECTLY.
:-)

Had to replace grease filter

  • Customer: Donald from Cottage Grove, OR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
Nice filter. Exact fit. Had a little ring to use to pull out to clean. Shipment was packed well.

Blower motor had frozen up.

  • Customer: Joe from Fair Oaks Ranch, TX
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 4 people found this instruction helpful
Removed front wooden kick panel(2 cross recessed screws).
Removed 2 bolts holding blower to floor. Loosened 2 vent clamp screws on vent from stove(2 clamps). Pulled vent off of blower housing. Removed blower from under stove. Using a nut driver, removed 4 nuts from blower and removed the motor cover & motor from the blower housing, removed 3 screws from motor cover and removed the motor cover from the motor. Ordered new motor. After new motor was rcvd (about 3 days plus wk end) I removed the squirel cage from the motor shaft using a metric allen wrench. Then removed the mounting clamp from the old motor by loosening 1 screw. Placed the motor clamp and the squirel cage on the new motor, then placed the motor cover on the motor. Placed blower mtg bkt and motor on blower housing w/ the 4 nuts removed earlier. Placed blower motor assy under stove being careful not to damage the exaust vent behind the blower motor as I carefully put the blower motor into the exhaust vent. Placed vent from stove on stove and blower housing and secured w/the 2 vent clamps removed earlier. Attached the blower motor base to the floor w/ 2 bolts. Wala........complete

Renters removed leveling legs from refrigerator. I don't know why!

  • Customer: Don from Frankfort, KY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I tilted the unit back enough to scew the new legs into the threaded holes.

Filter Worn Out

  • Customer: Thomas from Berlin, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
Remove cover and install

Burnner rusty and will not start with electric start.

  • Customer: Robert from Mary Esther, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 2 people found this instruction helpful
Removed and installed burners in less than 15 min with just a nut driver. Replacing the burn ere did not fix the starting problem, but replacing them did improve the hurried flame.

replaced the current warn-out grease filter

  • Customer: Joseph from East Greenwich, RI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
removed the old by pulling it out of track and replaced it with the new filter

Toggle switch was burned

  • Customer: Jian from Schenectady, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 2 people found this instruction helpful
The toggle switch I ordered is a little different then the original one. The original one has three head and one of the head is shared by two circles controlled by the switch. The switch I ordered has 4 head which mean it has two separate circles. I had to short circle the two middle heads to make it work. Other than this, the switch works perfectly!
All Instructions for the SEG196W
76-90 of 131