Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SEG196W Maytag > Instructions

SEG196W Jenn-Air Range - Instructions

All installation instructions for SEG196W parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SEG196W
61-75 of 131
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replaced the light /oven rocker switch

  • Customer: Ronald from Rochester Hills, MI
  • Difficulty: Very Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 2 people found this instruction helpful
The two mounting clips supplied with the switch would not fit onto the two studs in the die casted plate (too small) . In removing one of the old clips, the stud broke off. Thus I had to break off the other stud and drill out the area to allow two screws to be inserted to mount the switch securely.

oven fan/ight switch broken

  • Customer: Marc from Maineville, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 1 of 2 people found this instruction helpful
The hardest part was removing the old switch. It had locking washers that were very hard to remove. After that it was a breeze. Be sure to turn off the electricity to the oven.

I'm sure I saved a ton of money and wife was ecstatic, it had been broken for a year or more.

Broken switch would not turn on exhaust fan

  • Customer: Don from Nacogdoches, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
Removed 2 screws to get to old unit, unplug electric wire and pluged in new switch.
No problems, correct parts. Will look for other needed parts in the future.
Thanks

Blower motor had frozen up.

  • Customer: Joe from Fair Oaks Ranch, TX
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 5 people found this instruction helpful
Removed front wooden kick panel(2 cross recessed screws).
Removed 2 bolts holding blower to floor. Loosened 2 vent clamp screws on vent from stove(2 clamps). Pulled vent off of blower housing. Removed blower from under stove. Using a nut driver, removed 4 nuts from blower and removed the motor cover & motor from the blower housing, removed 3 screws from motor cover and removed the motor cover from the motor. Ordered new motor. After new motor was rcvd (about 3 days plus wk end) I removed the squirel cage from the motor shaft using a metric allen wrench. Then removed the mounting clamp from the old motor by loosening 1 screw. Placed the motor clamp and the squirel cage on the new motor, then placed the motor cover on the motor. Placed blower mtg bkt and motor on blower housing w/ the 4 nuts removed earlier. Placed blower motor assy under stove being careful not to damage the exaust vent behind the blower motor as I carefully put the blower motor into the exhaust vent. Placed vent from stove on stove and blower housing and secured w/the 2 vent clamps removed earlier. Attached the blower motor base to the floor w/ 2 bolts. Wala........complete

The stovetop gas regulator kept clicking in off position.

  • Customer: Preben from Fox River Grove, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 8 people found this instruction helpful
The spare part came within two days after I place the order on line. I drew a simple wire diagram of the faulty switch-regulator. Shut off the power to the stovetop, before removing the four terminals on the faulty switch-regulator. I pushed the old regulator up from the center pin and replaced it with the new regulator. The next step was to reinstall the four wire terminals using my wire diagram. Final step was to turn the power back to the stovetop and test the new switch-regulator.

No leveling legs

  • Customer: stephen from montgomery, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench (Adjustable)
  • 1 of 2 people found this instruction helpful
Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve

worn door seal on oven

  • Customer: Sarah from Albany, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
takes two people to put the oven door back in place but otherwise very simple as long as you keep all your screws and pads in place

light bulb went out in my oven

  • Customer: Janet from Ada, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 6 people found this instruction helpful
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Malfunctioning Switch on Jenn Air D156W

  • Customer: Mark from Coconut Grove, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 3 people found this instruction helpful
Just wanted to thank you for the great service. I ordered the part on Tuesday, it shipped on Wednesday and arrived on Thursday. I installed the switch in under :10 minutes on Friday and the old Jenn Air grill is running like new again.
Many thanks!

Downdraft fan would not operate with light/fan switch.

  • Customer: Alan from Pleasant Hill, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 3 people found this instruction helpful
Removed old switch, but when I tried to install the new one the round slide on retainers that hold the switch in place were cheaply made and broke. I had to go to the hardware store to find replacement parts. Electric terminals matched correctly and slipped off and on just fine. New switch works great.

The broiler would not heat. I saw a bad place in the element. Ordered a new one.

  • Customer: Henry from Smithfield, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 6 people found this instruction helpful
Received the new one. Installed it in 15 minutes. Thanks for the fast service.I will buy from you guys the next time I need a part ! Thank You, Henry

Old switch was difficult to remove and the push nuts provided with the new switch were too small to fit on the lid posts.

  • Customer: Chris from Wellesley, MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 1 of 3 people found this instruction helpful
Removed the old switch by essentially destroying it with a screw drive and pliers. Had to drive to the hardware store to purchase push nuts that fit.
.

Electronic Clock Assembly quit

  • Customer: Gayle from Lenoir City, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 4 people found this instruction helpful
It was easy to get apart. I drew out a schematic of where the wires were so I could put them back in the same place. I plugged them all back up and it worked! Only problem was, there was a dead mouse behind the panel! He had not chewed anything, so the unit just went out from age.

switch broke off and fell into oven cavity

  • Customer: alfio from piedmont, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 4 people found this instruction helpful
removed two screws, pulled up hardware / components, unplugged the old switch, (remember to switch off the circuit breaker!) the two 'fasteners' that are supposed to keep the switch tied to the cover panel did not fit, so i had to use epoxy to secure the switch. no problem though.

The old switch disintegrated and I lost all functionality of fan or light

  • Customer: Chris from Everett, WA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
The part I ordered is the perfect match for this stove. Replacement was a breeze. Take the 2 screws out that hold the switch housing, using an old dental pick, I pryed out the old washers, put the new switch in, used a small socket to push the new washers on, hooked up the wires, done. Gotta love partselect.com!
All Instructions for the SEG196W
61-75 of 131