Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SCG20200A

SCG20200A Jenn-Air Range - Overview

Get Parts and Repair Help for SCG20200A

If you know the range repair part you need, you can browse the list of all parts on the SCG20200A, or you can search by name or part description. You can also find your part by where it is located on the SCG20200A by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for SCG20200A parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.91

Light Bulb - 40W

Sold individually.

$31.07

Flat Style Oven Igniter Kit

The flat style gas oven igniter included in this kit has a body length of 3-3/4 inches. This kit comes with all of the pieces you need to replace longer ceramic igniters, though this kit can also replace short igniters. This igniter has an amperage range of 3.3 - 3.6 and does NOT replace round style oven igniters.

$16.57

Top Burner Igniter

This top burner igniter comes with a mounting bracket.

$23.99

Short Oven Sensor Kit

This temperature sensor detects the temperature within the oven cavity.

$19.22

Broiler Drawer Support - Front

$39.05

Inner Door Glass

Glass ONLY.

$4.63

Storage Drawer Wheel and Shaft

This wheel and shaft is used to open and close the bottom storage drawer of a range/stove.

$51.19

Bake Burner

$41.10

Door Hinge Kit

This oven door hinge assembly comes with two screws and is intended for use with many ovens. It can be used on either the left or right hand side.

$4.89

SCREW

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven would not work but the Broiler did

  • Customer: James from Ferndale, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 251 of 278 people found this instruction helpful
The oven had been working intermittently for a while and after repeated threats of starvation from my spouse I finally took a look even though it was summer and the grill was working fine. The Igniter would glow red when the oven was turned on but the gas would not flow to it no matter what the temperature setting. I searched online and found this site that ... read more

F1 code - gas over would not heat.

  • Customer: george from birmingham, AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 120 of 129 people found this instruction helpful
Repair tech checked oven and said the control panel was bad and needed to be replaced. The new control panel would cost over $450.00! I found that the oven sensor was bad and replaced it for $30.00. The old oven sensor had failed following a self cleaning cycle. I found that the wires coming out of it were burnt.

Replacing the oven sensor was ... read more

gas burner ignitor failure

  • Customer: roy from East Providence, RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 102 of 115 people found this instruction helpful
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed that rust and dirt ha... read more