Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SAV505DAWQ

SAV505DAWQ Maytag Washer - Overview

Get Parts and Repair Help for SAV505DAWQ

If you know the washer repair part you need, you can browse the list of all parts on the SAV505DAWQ, or you can search by name or part description. You can also find your part by where it is located on the SAV505DAWQ by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for SAV505DAWQ parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.63

Washer, Thrust

This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below....

$7.00

Retaining Ring

The metal retaining ring, which is under an inch long, holds the rear wheels on the axels of the dryer. The main reason why it would need to replaced is if the retaining ring has sprung out of place or is damaged. Some the symptoms could be that your dryer does not tumble, it makes a loud buzzing noise, or if it pumps, but will not spin. The tools needed for this project are a putty knife, 5/16 nut driver, and snap ring pliers. Refer to the installation video and diagram for further instructions and guidance. Customers ranked this replacement project as easy.

$3.02

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air...

$7.86

Adjustable Levelling Leg

If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locking nuts on the legs that are threaded. Your washer should be kept as close to the floor as possible. Your model might have rear legs that level themselves, or it might have threaded legs all around. Make sure the rubber feet have not worn out. Replace any missing or damaged legs and feet. This genuine OEM replacement part is sold individually, so be sure to order the amount you need.

$9.76

INLET HOSE

This hose can handle hot or cold water and is five feet long.

$3.02

Lid Hinge Mounting Screw

Sold individually.

$4.63

Spring Retaining Clip

This spring retaining clip is just under 1 inch long. The clip is made entirely of metal and is attached to the back wall of the washer, under the console. If your washer is vibrat...

$5.51

Hose Clamp

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.

$22.43

Idler Pulley Wheel

This wheel has a center metallic bearing. A dryer's idler pulley wheel serves to help the belt to rotate the drum.

$23.65

Drain Hose with Rubber Elbow

This hose attaches to the pump to help remove the water out of the washer.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water leaking on floor from "mysterious place underneath washer"

  • Customer: Bryan from Chicago, IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 43 of 48 people found this instruction helpful
Water was leaking on the floor during the wash cycle and especially during draining of the washer. I removed the front panel at ground level and watched while draining after a rinse.

I t was obvious that water was spraying from a hole in the rubber end of the hose (the hose is a fused assembly of a plastic section and a rubber section).

read more

unusually loud rumbling in spin mode, no spin out

  • Customer: Ralph from Moreno Valley, CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 28 of 33 people found this instruction helpful
removed outer enclosure to expose inside workings. removed all retaining springs to tub and transmission housing. Inverted tub to access agitator pulley and belt. Removed pulley and cut belt off.(I knew I was replacing it, anyway.)Had to remove large tub bracket to exchange new pulley for old. Disconnect bleach reservoir filler tubing on tub assembly. D... read more

sneakers broke fins off the agitator

  • Customer: David from Holcombe, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 26 of 28 people found this instruction helpful
I first grasped the fabric softner dispenser and pulled it up and off agitator. I then removed the bolt from the center of the agitator with a 1/2" socket, 8" extension and ratchet. I grasped the agitator assembly and pulled it up and off. Reversed the procedure to install. The bolt can be started by placing a piece of paper towel over the socket, then i... read more