Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SAV4655EWW

SAV4655EWW Maytag Washer - Overview

Get Parts and Repair Help for SAV4655EWW

If you know the washer repair part you need, you can browse the list of all parts on the SAV4655EWW, or you can search by name or part description. You can also find your part by where it is located on the SAV4655EWW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for SAV4655EWW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.63

Washer, Thrust

This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below....

$3.02

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.

$7.86

Adjustable Levelling Leg

If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locki...

$7.00

Retaining Ring

The metal retaining ring, which is under an inch long, holds the rear wheels on the axels of the dryer. The main reason why it would need to replaced is if the retaining ring has sprung out of place or is damaged. Some the symptoms could be that your dryer does not tumble, it makes a loud buzzing noise, or if it pumps, but will not spin. The tools needed for this project are a putty knife, 5/16 nut driver, and snap ring pliers. Refer to the installation video and diagram for further instructions and guidance. Customers ranked this replacement project as easy.

$3.02

Lid Hinge Mounting Screw

Sold individually.

$4.63

Spring Retaining Clip

This spring retaining clip is just under 1 inch long. The clip is made entirely of metal and is attached to the back wall of the washer, under the console. If your washer is vibrating and louder than usual during the wash cycle, your spring retaining clip could be faulty or damaged. Check the clip for visible damage, wear, and rust. If you notice any signs of damage, the part should be replaced. Remember to disconnect the power from your washing machine before starting this repair.

$9.56

INLET HOSE

This hose can handle hot or cold water and is five feet long.

$23.65

Drain Hose with Rubber Elbow

This hose attaches to the pump to help remove the water out of the washer.

$22.43

Idler Pulley Wheel

This wheel has a center metallic bearing. A dryer's idler pulley wheel serves to help the belt to rotate the drum.

$2.96

Screw

Sold Individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Spin cycle sounded like freight train

  • Customer: Mike from Houston, TX
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Socket set
  • 86 of 94 people found this instruction helpful
Spin cycle sounded like freight train, bad bearing, apparently they all fail the same way, this revised parts kit should prevent premature failure in future.

The following is easy for an experienced mechanic of any type, fully doable by an accomplished DYI'er, between this writeup and the kit instructions (which I do not fully follow) you should b... read more

Maytag Washer Leaks, Noisy

  • Customer: RAYMUND from WEST COVINA, CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable)
  • 47 of 54 people found this instruction helpful
1. I unplugged the machine. Using a socket wrench set, I removed the washer housing (bottom, front and sides) and flipped over the top to its service position. This exposes all the inner parts of the washer.
2. I pulled out the softener cup, unbolted the auger using a socket wrench with a long adaptor. I then pulled out the auger, exposing the "Seal Nut... read more

Water leaking on floor from "mysterious place underneath washer"

  • Customer: Bryan from Chicago, IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 42 of 47 people found this instruction helpful
Water was leaking on the floor during the wash cycle and especially during draining of the washer. I removed the front panel at ground level and watched while draining after a rinse.

I t was obvious that water was spraying from a hole in the rubber end of the hose (the hose is a fused assembly of a plastic section and a rubber section).

read more