Models > SAV4655EWQ

SAV4655EWQ Maytag Washer - Overview

Get Parts and Repair Help for SAV4655EWQ

If you know the washer repair part you need, you can browse the list of all parts on the SAV4655EWQ, or you can search by name or part description. You can also find your part by where it is located on the SAV4655EWQ by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for SAV4655EWQ parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.54

Thrust Washer

Order within the next 11 hrs and your part ships today!
$5.04

Retaining Ring

Sold individually.

Order within the next 11 hrs and your part ships today!
$2.70

Hose Clamp

Order within the next 11 hrs and your part ships today!
$41.16

Drain Pump

This pump is attached to the motor and helps expel water from the washing machine. It is activated after the spin speed is maintained for a specific period of time.

Order within the next 11 hrs and your part ships today!
$2.70

Screw

This screw is sold individually.

Order within the next 11 hrs and your part ships today!
$4.55

Adjustable Levelling Leg

Sold Individually. This adjustable leveling leg comes with a stop nut.

Order within the next 11 hrs and your part ships today!
$2.07

Lid Hinge Mounting Screw

Sold individually.

Order within the next 11 hrs and your part ships today!
$19.50

Selector Knob

Sold Individually. This knob may differ in appearance, but functions same as original.

Order within the next 11 hrs and your part ships today!
$19.16

Idler Pulley Wheel

This wheel has a center metallic bearing. A dryer's idler pulley wheel serves to help the belt to rotate the drum.

Order within the next 11 hrs and your part ships today!
$5.91

Spring Retaining Clip

This front cover spring retaining clip is not quite an inch long. It is made entirely of metal and is used for some washing machines.

Order within the next 11 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Spin cycle sounded like freight train

  • Customer: Mike from Houston TX
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Socket set
  • 63 of 67 people found this instruction helpful
Spin cycle sounded like freight train, bad bearing, apparently they all fail the same way, this revised parts kit should prevent premature failure in future.

The following is easy for an experienced mechanic of any type, fully doable by an accomplished DYI'er, between this writeup and the kit instructions (which I do not fully follow) you should b... read more

Washer made loud noise on spin only

  • Customer: Donald from Glassboro NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 45 of 55 people found this instruction helpful
Removed agitator, inner and outer tub, balance springs, motor assembly,transmission to get to bearing and seal in tub bottom. read more

Maytag Washer Leaks, Noisy

  • Customer: RAYMUND from WEST COVINA CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 33 of 38 people found this instruction helpful
1. I unplugged the machine. Using a socket wrench set, I removed the washer housing (bottom, front and sides) and flipped over the top to its service position. This exposes all the inner parts of the washer.
2. I pulled out the softener cup, unbolted the auger using a socket wrench with a long adaptor. I then pulled out the auger, exposing the "Seal Nut... read more