Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SAV405DEWW

SAV405DEWW Maytag Washer - Overview

Get Parts and Repair Help for SAV405DEWW

If you know the washer repair part you need, you can browse the list of all parts on the SAV405DEWW, or you can search by name or part description. You can also find your part by where it is located on the SAV405DEWW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for SAV405DEWW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$5.15

Washer, Thrust

This washer is 3/4 inches in diameter.

$5.15

Hose Clamp

$5.10

Screw, 8/18 x 3/8

This screw is sold individually.

$21.40

Drain Hose with Rubber Elbow

This hose attaches to the pump to help remove the water out of the washer.

$10.35

Adjustable Levelling Leg

Sold Individually. This adjustable leveling leg comes with a stop nut.

$10.11

Retaining Ring

This metal retaining ring is well under an inch long. Use it for your Maytag brand clothes washer or your clothes dryer.

$5.15

Lid Hinge Mounting Screw

Sold individually.

$28.76

V-Style Spin and Agitate Belt - 28-3/4 inches long

This v-style spin and agitate belt is 28-3/4 inches long and half of an inch wide. It is all black in color and made entirely of rubber.

$21.03

Idler Pulley Wheel

This wheel has a center metallic bearing. A dryer's idler pulley wheel serves to help the belt to rotate the drum.

$13.29

INLET HOSE

This hose can handle hot or cold water and is five feet long.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Spin cycle sounded like freight train

  • Customer: Mike from Houston, TX
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Socket set
  • 81 of 88 people found this instruction helpful
Spin cycle sounded like freight train, bad bearing, apparently they all fail the same way, this revised parts kit should prevent premature failure in future.

The following is easy for an experienced mechanic of any type, fully doable by an accomplished DYI'er, between this writeup and the kit instructions (which I do not fully follow) you should b... read more

Maytag Washer Leaks, Noisy

  • Customer: RAYMUND from WEST COVINA, CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable)
  • 45 of 52 people found this instruction helpful
1. I unplugged the machine. Using a socket wrench set, I removed the washer housing (bottom, front and sides) and flipped over the top to its service position. This exposes all the inner parts of the washer.
2. I pulled out the softener cup, unbolted the auger using a socket wrench with a long adaptor. I then pulled out the auger, exposing the "Seal Nut... read more

Washer made loud noise on spin only

  • Customer: Donald from Glassboro, NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 45 of 58 people found this instruction helpful
Removed agitator, inner and outer tub, balance springs, motor assembly,transmission to get to bearing and seal in tub bottom. read more