Models > SAV365AAWW

SAV365AAWW Maytag Washer - Overview

Get Parts and Repair Help for SAV365AAWW

If you know the washer repair part you need, you can browse the list of all parts on the SAV365AAWW, or you can search by name or part description. You can also find your part by where it is located on the SAV365AAWW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for SAV365AAWW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.54

Thrust Washer

Order within the next 6 mins and your part ships today!
$5.04

Retaining Ring

Sold individually.

Order within the next 6 mins and your part ships today!
$2.70

Hose Clamp

Order within the next 6 mins and your part ships today!
$41.16

Drain Pump

This pump is attached to the motor and helps expel water from the washing machine. It is activated after the spin speed is maintained for a specific period of time.

Order within the next 6 mins and your part ships today!
$31.95

Spin Belt

This v-shaped spin belt helps transfer power from the motor to the transmission to help pump the water in and out of the washer. It also helps runs the spin cycle in the washer.

Order within the next 6 mins and your part ships today!
$2.70

Screw

This screw is sold individually.

Order within the next 6 mins and your part ships today!
$4.55

Adjustable Levelling Leg

Sold Individually. This adjustable leveling leg comes with a stop nut.

Order within the next 6 mins and your part ships today!
$7.00

Hose Clamp

This hose clamp is sold individually.

Order within the next 6 mins and your part ships today!
$2.07

Lid Hinge Mounting Screw

Sold individually.

Order within the next 6 mins and your part ships today!
$19.50

Selector Knob

Sold Individually. This knob may differ in appearance, but functions same as original.

Order within the next 6 mins and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Belt wore out

  • Customer: Bruce from Medina OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 127 of 148 people found this instruction helpful
Had to remove pump-not easy. Nothing wrong with pump, but had to trash it to get it off the motor shaft, so I had to replace it, too.

Pop up top of cabinet and remove front panel. (I leaned unit back against a wall to facilitate internal access once panel was removed.)


Remove motor assy - 4 screws & connector.

Remove ... read more

Spin cycle sounded like freight train

  • Customer: Mike from Houston TX
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Socket set
  • 64 of 68 people found this instruction helpful
Spin cycle sounded like freight train, bad bearing, apparently they all fail the same way, this revised parts kit should prevent premature failure in future.

The following is easy for an experienced mechanic of any type, fully doable by an accomplished DYI'er, between this writeup and the kit instructions (which I do not fully follow) you should b... read more

DRIVE PUMP LEAKED

  • Customer: Stephen from Laveen AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 57 of 67 people found this instruction helpful
It took some trial and error but overall not a difficult project.

1. Take the front covers off.
2. Undo the pully spring to loosen belt
3. Remove belt off idler pulley wheel and free up belt from the large wheel.
4. Disconect the wiring harness and the hoses.
5. Undo the motor mounting bolts (4)
6. Take motor out of wash... read more