Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SAV2655AWW

SAV2655AWW Maytag Washer - Overview

Get Parts and Repair Help for SAV2655AWW

If you know the washer repair part you need, you can browse the list of all parts on the SAV2655AWW, or you can search by name or part description. You can also find your part by where it is located on the SAV2655AWW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for SAV2655AWW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.63

Washer, Thrust

This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below....

Order within the next 1 hr and 27 mins and your part ships today!
$3.02

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.

Order within the next 1 hr and 27 mins and your part ships today!
$7.86

Adjustable Levelling Leg

If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locki...

Order within the next 1 hr and 27 mins and your part ships today!
$7.00

Retaining Ring

The metal retaining ring, which is under an inch long, holds the rear wheels on the axels of the dryer. The main reason why it would need to replaced is if the retaining ring has sprung out of place or is damaged. Some the symptoms could be that your dryer does not tumble, it makes a loud buzzing noise, or if it pumps, but will not spin. The tools needed for this project are a putty knife, 5/16 nut driver, and snap ring pliers. Refer to the installation video and diagram for further instructions and guidance. Customers ranked this replacement project as easy.

Order within the next 1 hr and 27 mins and your part ships today!
$3.02

Lid Hinge Mounting Screw

Sold individually.

Order within the next 1 hr and 27 mins and your part ships today!
$4.63

Spring Retaining Clip

This spring retaining clip is just under 1 inch long. The clip is made entirely of metal and is attached to the back wall of the washer, under the console. If your washer is vibrating and louder than usual during the wash cycle, your spring retaining clip could be faulty or damaged. Check the clip for visible damage, wear, and rust. If you notice any signs of damage, the part should be replaced. Remember to disconnect the power from your washing machine before starting this repair.

Order within the next 1 hr and 27 mins and your part ships today!
$9.56

INLET HOSE

This hose can handle hot or cold water and is five feet long.

Order within the next 1 hr and 27 mins and your part ships today!
$37.73

BELT- SPIN

This v-shaped spin belt helps transfer power from the motor to the transmission to help pump the water in and out of the washer. It also helps runs the spin cycle in the washer.

Order within the next 1 hr and 27 mins and your part ships today!
$5.51

Hose Clamp

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washe...

Order within the next 1 hr and 27 mins and your part ships today!
$23.65

Drain Hose with Rubber Elbow

This hose attaches to the pump to help remove the water out of the washer.

Order within the next 1 hr and 27 mins and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Belt wore out

  • Customer: Bruce from Medina, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 173 of 199 people found this instruction helpful
Had to remove pump-not easy. Nothing wrong with pump, but had to trash it to get it off the motor shaft, so I had to replace it, too.

Pop up top of cabinet and remove front panel. (I leaned unit back against a wall to facilitate internal access once panel was removed.)


Remove motor assy - 4 screws & connector.

Remove ... read more

Spin cycle sounded like freight train

  • Customer: Mike from Houston, TX
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Socket set
  • 86 of 94 people found this instruction helpful
Spin cycle sounded like freight train, bad bearing, apparently they all fail the same way, this revised parts kit should prevent premature failure in future.

The following is easy for an experienced mechanic of any type, fully doable by an accomplished DYI'er, between this writeup and the kit instructions (which I do not fully follow) you should b... read more

Drive Pump Leaked

  • Customer: Stephen from Laveen, AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 68 of 80 people found this instruction helpful
It took some trial and error but overall not a difficult project. 1. Take the front covers off. 2. Undo the pully spring to loosen belt 3. Remove belt off idler pulley wheel and free up belt from the large wheel. 4. Disconect the wiring harness and the hoses. 5. Undo the motor mounting bolts (4) 6. Take motor out of washer and remove the 3 screw... read more