Models > SATF7000FS0 > Instructions

SATF7000FS0 Electrolux Washer - Instructions

All installation instructions for SATF7000FS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SATF7000FS0
76-90 of 202
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drum was banging around when spooling up and slowing down

  • Customer: Matthew from Pullman WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
The front lower access panel pops off with two Philips head screws. From there, the white pins holding the hold broken shock absorbers can be removed by pressing their locking tab down and pushing them free of the bushing.

After pulling the old, broken items out, the new ones are reinstalled the same way: place the metal end towards the drum, push the white pin through the bushing (only one way is correct) and you're almost done. Reinstall the front panel and get back to having a quiet washing machine!

Broken washer Drum Vane

  • Customer: KAS from LYNNWOOD WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
I follow the instruction that comes with the part.The only thing different is i use WD-40 , to slide the vane better.

$500 Repair for $25, well worth the struggle!

  • Customer: beverly from Miami FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Wrench(Adjustable)
  • 1 of 2 people found this instruction helpful
I replaced both shock absorbers that hold the drum on a front loading washer. They both snapped at the base and have since been replaced by a different style shock absorber. There are 2 pins that hold each part in place. I took 5 minutes to replace 3 pins and about an hour to replace the last one, which was in a very tight spot. After much sweating and swearing, I managed to get the pin back in. Was it worth it? ABSOLUTELY! Partsselect.com is a dream for straightforward repairs. This is the second repair I have done on this machine (which is less than 5 years old) and both repairs have cost less than $30.

Washing Machine would drain but not spin.

  • Customer: Kelly from Henderson NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
It was a very easy fix. Called a repairman and they wanted 350.00 to come out. Ordered the door lock and switch assembly for 76.00 and it was fixed in 15 minutes. Thank you for shipping the part so fast. Much appreciated.

Machine bounced all over the room

  • Customer: Stuart from Canton MI
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 3 people found this instruction helpful
I followed the great instructions provided on the site and had the old broken struts out in no time. The new ones went in without a hitch and the time it took me to unscrew and rescrew in the back of the machine was longer than the time it took me to replace the broken parts.

Bouncing and noisy washer

  • Customer: Chad Trainum from Albuquerque NM
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 1 people found this instruction helpful
I had read the instructions and suggestions on the site. The product arrived with a good set of instructions. I used the deep socket to push in the "catch" on the pins. Once the catch is depressed I pulled and twisted a bit to get the pins out. After I pulled both broken shocks out I replaced them as instructed. I did use a long wooden dowel to get the pins all the way in. Read the instructions and follow what they tell you and it'll be done in under 15 min.

washer went off balance, barrel in washer was loose

  • Customer: Marcie from Montesano WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Disconnected hoses, unplugged, took off top and back of washer. Removed the white plastic thingys that retained the broken shock absorbers. Installed the new ones, using a hammer and 1/2" copper pipe section to place white plastic thingys. Put back, top on. Reconnected hoses, plugged in. Presto!

Drum would sway out of balance

  • Customer: Jeffrey from Woodinville WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 1 people found this instruction helpful
Followed the kit instructions to the letter. working around tight clearences was really the only thing to slow me down. The other posts tell the rest of the story better than I can.

broken shock heads-up!

  • Customer: James from Almond NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 1 people found this instruction helpful
If you have a broken shock (or two) there's a strong possibility that the failure caused, or was caused by, a failure of the "spider" that attaches the inner drum to the "drive shaft". If this is the case, the problem is likely terminal for your washer... unless you purchased a rip-off service contract. The parts will cost upwards of $250 and the bearings and seals that must be dealt with cry-out for a service tech and the associated labor cost. Between the poor engineering and lousy service, I will no longer be purchasing Sears appliances. I did *not* get my money's worth from this washer and Sears has not made good.

knocking noise when washer changed directions

  • Customer: Randy from Okeechobee FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
First I removed two screws in front lower panel to access lower portion of washer machine. Use pilars to push four plastic pins from each end of two vibration/shock abs. Job was very easy and took less than 30 minutes to complete.

Broken shock

  • Customer: Scott from Pearland TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 1 people found this instruction helpful
My washer was leaking a bit on the left side, apparently from the place water enters from filler. I spent a bit of time inspecting that side of the thing and my jaw dropped when I finally saw the other side of the washer, the upper shock was broken off and the thing was not connected.

I got my parts fast and removing the pins was a bit troublesome but some from access standpoint, but it wasn't hard - just took some extra effort and prying from the head side. Seems to run better with new shocks and no more leaking so far.

both left and right shock absorbers had broken into they are plastic on my front load galeriey series washer

  • Customer: Les from Belleview FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
I removed the bottom front panel ( 2 screws) and about 8- 10 inches back were the shock absorbers...the one on the left was easiest nothing in way I squeezed the locking tab and pushed the pin thru to remove the shock absorber...on the right side was a little tricky but got my arm round the drain hose and small pump and pushed that pin thru as well...installed new shocks and was good to go...I did call a local repair business here in belleview florida was told the shocks themselves would cost 37.00 for the pair and about 150 - 175 in labor...I paid 22.00 from parts select and did my own labor thanks for all the help...les

Broken shock - slight leak

  • Customer: Duffy from Wheaton IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
You could do the replacement by just removing the maintenance panel on the front, but removing the rear panel gives you more options for getting at the shocks.

The front panel comes off with 2 screws, the back has a lot of screws holding it on, a cordless drill is the way to go.

Prying on the head of the plastic bolt with a pair of needle-nosed pliers while pushing down on the tab seemed to work well. I did have to remove a small box that houses electronics to remove the one from the right side.

While I was in there, I tightened up the numerous bolts that holds the drum shell together. Machine is much smoother now and no leaks.

Washer off balance caused springs, shocks to break

  • Customer: Lois from Pasadena TX
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 1 people found this instruction helpful
Took off the front, and put a come along to rafters in garage to lift tub.
Replaced shock asborers, waited for spring kit to be delivered, replacing all.
Still isn't working need to check wiring to some compoments to see if a wire is broken.
Hope to have it washing soon

Washer drum would not spin

  • Customer: Annie from Santa Clara CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 4 people found this instruction helpful
For some time, our washer's door was vibrating and making noise during the spin cycles. Then after washing a large blanket, the drum stopped spinning all together. I was able to slide the top of the washer off after undoing the screws in the back and then following the directions, found that the error code was for the washer door. The drum would not spin because it thought that the door was open, confirming what we thought, the door lock and switch assembly were bad.
I was able to unscrew the assembly from the front, then reach down and after ordering the new part, disconnect the 3 cables, remove the old part then redo the cables on the new assembly and Voila...working washer, woo hoo!
All Instructions for the SATF7000FS0
76-90 of 202