Models > SA31HA-10XS-R > Instructions

SA31HA-10XS-R Admiral Range - Instructions

All installation instructions for SA31HA-10XS-R parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SA31HA-10XS-R
1-15 of 34
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

spring broke on one side of door hinge

  • Customer: Travis from Lexington OK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 8 people found this instruction helpful
Pulled the stove out, removed the sides and attatched the new springs( replaced both while the stove was out). Worked like new and put the stove back.

leak

  • Customer: George from Plainville MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
removed then installed new unit by hand. received order the next day-am. delivery time great.

the burner knobs broke off

  • Customer: Belinda from Downey CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 12 people found this instruction helpful
I put the 2 burner knobs on and now I have 4 working burners....Thanks for the quick delivery....

Gas manifold had holes in it.

  • Customer: Mr. J.C. from Haines City FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
Removed locking wire from bottom burner assembly then I pulled the element out and replaced with the new one.

HAD TO CHANGE THE KNOB I COULD NOT READ IT

  • Customer: ANDREA from CORNING CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 6 people found this instruction helpful
PULLED THE OLD KNOB OFF AND PUT THE NEW ONE ON. ONLY THING THAT WAS DIFFICULT WAS MAKING SURE THE KNOB WAS THE RIGHT ONE BECAUSE THE INSTRUCTIONS KEPT LEADING ME BACK TO A DIFFERENT BRAND OF APPLIANCE BUT SINCE THE PHOTO LOOKED ALIKE I WENT AHEAD AND GOT IT.

A high flame was coming out of the side of the burner

  • Customer: KAY from BRIDGEPORT CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
Easy......pulled out the old one easily and popped in the new one.......saved a lot of money...no repair bill for either diagnostic fee or assembly fee ...No mark up for the part either. Very happy mom!

original light grey color grates stained and unsightly--no amount of scrubbing or cleansers would make them look nice.

  • Customer: Linda from Jenison MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 10 people found this instruction helpful
Opened the box and took out the black color grates~~removed discolored grates and put the new ones on. Looks like a brand new stove and much nicer to look at as it is the first thing you see when you enter the kitchen.

Install valve knobs

  • Customer: Donald from Peebles OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 5 people found this instruction helpful
This was not a difficult task. I just slid the valve knob on the shaft, repair was complete. This was a very easy diy project.

Freont burners of both units had rusted though over the years of boilover.

  • Customer: Angelo W. from Chirfland FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Lifted lid, removed old burner units, replace with new ones. In Less than two min. was back up and cooking.

Door Spring Broke

  • Customer: Thomas from Van Nuys CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
Removed 7 screws on sides and one on top of stove. Replaced both springs (only one was broken but did both). Took around 15 to 30 minutes from start to finish.Fastest shipping in history during holidays without paying anything extra.

Broken burner knobs on stove.

  • Customer: Barbara L. from Tewksbury MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
Just replaced the old burner knobs with the new !!!

30 year old gas stove needed a new burner assembly.

  • Customer: Caroline from South Windsor CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
We lifted up the stove top, slipped the burner assembly in. It fit! who knew that we could get a part to an old stove without the model number, just by looking at a picture of the part! Terrific!

needed a new knob

  • Customer: Clayton from Shortsville NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
pulled the old one off and push the new one on

new knob

  • Customer: Marvin from Pahrump NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
Pulled one knob off and pushed the other one on.

Pilot light would go out when oven was turned off but still allowed gas.

  • Customer: Steven from Oklahoma City OK
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set, Wrench(Adjustable)
  • 3 of 9 people found this instruction helpful
l removed the top section after the grates. Then l took the phillips screws out of the three brackets which hold the L brace which supports the controls,thermostat and the regulator. Only because l did not have a closed-end ratchet wrench for 1/4" and l could not locate my 1/4" socket for my small rachet. l disconnected all gas lines and the thermocouple, then l used the power screwdriver without the apex which makes it a great power 1/4" nutdriver and took out the two screws holding the thermostat. Then l just reversed all the steps installing the new thermostat and once l got the air out and gas was pure l lit the pilot lights and everything worked great. And l adjusted my top burner pilot lights a little higher to prevent them from gettig blown out so easy. Done deal.
All Instructions for the SA31HA-10XS-R
1-15 of 34