Quick Question!

Have you ever purchased from PartSelect.com before?

Models > S8757W0

S8757W0 Roper Range - Overview

Get Parts and Repair Help for S8757W0

If you know the range repair part you need, you can browse the list of all parts on the S8757W0, or you can search by name or part description. You can also find your part by where it is located on the S8757W0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for S8757W0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$11.12

Surface Burner Plug-In Block Kit

The surface burner plug-in block kit features a newer-style terminal block. This kit is designed for use with ranges and cooktops. This terminal block is how the coil element on yo...

Order within the next 6 hrs and your part ships today!
$121.20

Drive Motor with Pulley

This motor fits most Whirlpool incorporated dryer brands before 1996. NOTE: Pulley is NOT available separately.

Order within the next 6 hrs and your part ships today!
$31.06

Temperature Sensor

This temperature sensor is used to measure the inside temperature of a self-cleaning oven. Its 1000-ohm resistance increases with temperature. The sensor has male leads, is 6 inche...

Order within the next 6 hrs and your part ships today!
$45.94

Round Carborundum Oven Igniter

This round style gas oven igniter, or also known as a broil or bake igniter, has an amperage range between 2.5 and 3.0. It glows white hot to ignite the gas for the oven. The igniter does this by attracting electrical currents through the safety valve to open it. *Please note: this does not replace the flat style igniters. If your gas igniter does not start, glows but does not light, or produces little to no heat when baking, replacing this part could be the solution to your problem. Refer to the diagram provided by the manufacturer for further instructions and guidance.

Order within the next 6 hrs and your part ships today!
$3.02

Hex Nut

This 10-32-inch hex nut works with multiple appliances in your home as a fastener. This specific model is sold individually. Hex nuts usually have 6 even sides and together they ar...

Order within the next 6 hrs and your part ships today!

STIRRER COVER ***

ELEMENT

CONTRL-PWR

GLASS-D00R

Cushion-Oven Door (3 Req)

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

F3 Error message

  • Customer: Charles from Brecksville, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 141 of 180 people found this instruction helpful
Two screws remove the front of the sensor (put a pan under the sensor to catch the screws), One nut removes the rear cover to access the rear of the sensor. Separating the two halves of wiring harness takes a little dexterity. BIG TIP! Tie a string to the back of the sensor wire and pull the sensor out from the front making sure the string still shows thru t... read more

Make humming noise when pressing start button. Would not start

  • Customer: James from Moscow, IA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 82 of 93 people found this instruction helpful
After looking on the website for advice I walked throught the simple steps of disassembling the front, removing the drum, removed the back, disconnected the wire harness. Then removed the blower housing in the back. The blower, mounted on the back side of the motor was very tight. I used a pipe wrench wedged in place and help by my 10 year old Grand-daugh... read more

The lower burner would not ignite.

  • Customer: Mark from Rego Park, NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 70 of 75 people found this instruction helpful
First I removed the oven racks. Then I loosened the two screws in the back of the oven floor and figured out how to remove it. Then I loosened the two screws at the front of the diverter and, with some pushing and pulling and twisting, was able to get that to come out, too. Then I tried lighting the oven and noticed that the igniter was not glowing. When... read more