S5200E6WW General Electric Washer - Instructions

I pulled the top of the agitator off (the softener dispenser) then pulled the agitator itself off. I had to pull with some force. I used the socket wrench to remove the bolt on top of the agitator coupling. I then pulled off the old agitator coupling, replaced it with the new part. Used the socket wrench to tighten the new bolt. Lined up the slots on the new coupling with the agitator top, it slid on with a little resistance. The last part to replace was the softener dispencer.

Just push the new knob over the metal pin

First I removed the softener dispenser then I grabbed the agitator at the bottom and with a tug completely removed it. I took the new part out of the box and lowered it down over the hub in the bottom of the washer and gently pushed it until it snapped in place. Then I re-installed the old fabric softener dispenser and the job was complete.

replaced the dual water inlet valve

I unplugged the washer, removed the 4 knobs and unscrewed the 4 screws from the top of the front panel and moved it forward. I then disconnected the wiring and the 5 screws that hold the control assembly in place. I then reversed the steps with the new part. I have used the washer 3 times since the repair and the washer works perfect.

I laid the washer on its front and removed enough screws to fold the bottom out enough to reach it. I used a wire tie to secure the belt to main pulley and slipped it on the drive. This would have been nearly impossible without the install tool as it stopped the belt from slipping off of the drive. It was simple to turn the pulley clockwise to walk the belt onto it. The whole repair took about 1/2 hour, would have been less if I had used the wire tie at the very beginning.

pushed replacement knob on shaft of dryer. machine works better than new. took less than 24 hours from time of order to time of delivery to my house.

Installed a new mixing value. Repair went quickly and easily. Repaired machine working great. Easy ordering and the prompt shipping impressed us Greatly!! Thank you!

at 1st, i call GE for service, but i have to wait for the next available field service engineer which is 7 to 8 days to come to my place to check on the washer. the cost is $99.00(non refundable) and then he will order the parts needed for repair another 2 to 3 days. then i decided to buy the parts myself online,and google the web on "how to fix the washer that stopped agitating" everythings in there,with video instruction. pull the agitator up and out by grabbing on to its base. inside, the knot was corroded and the o ring worn out,but really easy to remove with the 11mm socket. the coupling kit although looks different,fit perfectly. insert says its an upgrade of the old model. toss the old and replace with the new, no sweat! now it's shaking like crazy.

Removed the four torx-head screws on the top of the washer. Pulled the control panel forward. Removed the four screws on the back of the washer and the two screws that held the dual valve on. These six screws required a nut driver. Pulled the small hose off the old valve. Then reversed the procedure. Total time to replace the faulty old part was about ten minutes. With saftey in mind, disconnect the electrical cord and shut the water valves off at the wall.

Viewed the step by step how to and was able to complete repair all has worked well great info sight!

I followed the on-line video with just one exception and I had the old part off in less than 5 minutes. I ordered the part on Saturday afternoon and I had the part in hand by Wednesday morning at around 11:00 am. I spent less time installing the coupling kit than it took to take it apart and had 2 loads of clothes done before going to work on second shift. I would recommend anyone needing help contact Parts Select. They were great and very helpful.

The agitator is the tough thing to remove, I took a previous posters advice and used a rope and 2 boards to pull it up. I will describe it as many short ropes but it can be done without cutting the rope if you think a lot about it. loop the a rope under the agitator so its under 1/2, loop another rope under the other side. tie both loops so you can slide a board in each across the top of the washer. Then tie the 2 loops together on 2 sides down near the bottom of the agitator otherwise they will come out from under it when you pull. then slide the boards in the loops and lift up pulling up the agitator.That is the hard part. Remove the bolt on the coupling, and pull it off. The new one had to be lightly hammered on with a rubber mallet, then use the new bolt. the Agitator slide down and with a push down it popped on. Putting the new part on only took 15 min, removing the broken one took about 45 min. Washer is woking great now ! Saved over $100 or buying a new washer !

Inside the appliance is an instruction sheet that describes replacing the part and followed it mostly. To improve your instructions, pictures with the instructions are much more effective and easier to understand.

Took out the old part and easily replaced it with the new part.