Quick Question!

Have you ever purchased from PartSelect.com before?

Models > S3700E4WW

S3700E4WW General Electric Washer - Overview

Get Parts and Repair Help for S3700E4WW

If you know the washer repair part you need, you can browse the list of all parts on the S3700E4WW, or you can search by name or part description. You can also find your part by where it is located on the S3700E4WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for S3700E4WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$7.84

Tub Dampening Strap

Appliance would take 4 straps. It is recommended to replace all 4 at the same time. They keep the tub in the center of the cabinet. Sold individually.

$9.63

Agitator Coupling Kit

Washing machine agitator drive bell with bolt. It connects the transmission drive shaft to the agitator base. *NOTE: Hold down bolt not sold separately.

$32.93

Agitator

This plastic dual action agitator is white in color. It is approximately eighteen inches tall with a base diameter of about 12-1/4 inches.

$12.71

Drain Hose - 4 1/2' Long

$7.52

Tub Seal

The main tub seal is located between the transmission and the outer tub. It's the primary water seal in the outer tub for the transmission-shaft. This seal is difficult to replace ...

$6.59

Timer Knob Clip

$44.08

Drain Pump and Motor Assembly

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.

$10.69

Knob and Clip

$11.33

V-Style Drive Belt

$6.59

Tub Bearing

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

One of eight clips broke off of the agitator assy allowing the assembly to come lose on heavy loads.

  • Customer: Paul from Carneys Point, NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 577 of 604 people found this instruction helpful
I replaced the coupling by only having to remove one bolt with a socket wrench. Once replaced I installed the new assy over the coupling making sure ro align the splines then pushing down until the assy snapped into place. Easy. read more

Washing Machine was not draining water from tub.

  • Customer: Gerald from Midlothian, VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 248 of 263 people found this instruction helpful
1. Drained the wash tub by taking the drain hose from the back of the washing machine and dropping it below the tub - water flowed out of hose a lot easier than trying to suck water out of tub using a pump (tried this on the first time I tried to fix washer). (Washing machine on 2nd floor of house and didn't want water running on floor)
2. Removed the... read more

broken dampening strap and loose agitator

  • Customer: molly from laguna niguel, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 208 of 218 people found this instruction helpful
first remove the front washer cover by finding the two pressure clips that hold it to the top lid. gently push the putty knife into the clips one at a time. this will raise and separate them from the front panel. the panel will tilt forward and u can now remove it from the bottom clips by sliding it up and out. to open the top cover u remove the two 1/4 in s... read more