Models > RVM1535DM2WW > Instructions

RVM1535DM2WW Hotpoint Microwave - Instructions

All installation instructions for RVM1535DM2WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RVM1535DM2WW
76-90 of 183
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

glass light lens was broken, had collected grease, was dark.

  • Customer: William from Littleton CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Simply removed screw, pulled down light holder, unfoled the metal tabs, took out the broken pieces and replaced the glass lens and light bulb.

Glass Carousel Cooking Tray Broke

  • Customer: Gary from Fernandina Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
I received the tray and place it in the microwave for a perfect fit. My wife is so happy.

light bulb burned out

  • Customer: Lois Jane from Fernley NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
took out several screws dropped down the panel under the microwave and unscrewed the bulb and put the new one in. It was a simple job.

Broken light socket

  • Customer: Richard from Batavia OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Turned the power to the unit off. Removed seven- (7) small screws from the base plate, not removing the rear screws. The plate dropped a few inches allowing me to get to the light socket.

I removed one- (1) screw that allowed the socket to be removed. I then detached the two- (2) electrical leads. I now installed the new socket, replacing the leads and the screw along with a new bulb. I pushed the bottom plate back into the up position and replaced the seven- (7) screws.

Turned the power back on and we were good to go.

Bulb was burnt out

  • Customer: Judy Ann from Fort Pierce FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Just unscrewed the screw holding the lens, unscrewed the bulb and put the new bulb in. Simple

Interior Light Out

  • Customer: Steven from Waldorf MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1 of 3 people found this instruction helpful
Removed Cover Plate,
Removed back cover
Bulb disintegrated removed base with pliers
Screwed in new lamp
Replaced cover
Done

Broken lens.

  • Customer: Gary from Warren MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Used a phillips head screw driver and loosened the lens frame under the microwave. Removed the broken lens and replaced it with the lens ordered. Put the lens frame back in place and secured it with the phillips head screw.

light lens broke a couple of years ago

  • Customer: KAREN from MANSFIELD MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
unscrewed the screw, pried up metal tabs that hold in light lens. took out broken pieces, slid in new light lens re-secured tabs with fingers, screwed in the screw again.

light out over stove

  • Customer: virginia from hilton head island SC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
so easy, but how do i turn light off?

Part recieved next day. thanks so much

Broken light lense

  • Customer: George from Marana AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed one screw, installed new lense in lense frame, rescrewed. Done.

bulb burned out -cracked holder lamp

  • Customer: Terry from Justice IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
pluged wires back on ,placed lamp holder and bulb back and replaced screws

the glass tray was broken in a move

  • Customer: Harriet from Crystal Spring PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
just set the new carousel tray into place inside the microwave.
but your site made it so easy to order. will keep the site as a favorites.
thank you

UNDERNEATH LIGHT ON MICROWAVE WOULD NOT COME ON.

  • Customer: MARY from PLYMOUTH MA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
MY SON=LAW DID REPAIR BECAUSE i AM ELDERLY AND IT WAS NECESARY TO REMOVE THE BOTTOM PLATE OF THE MICROWAVE WHICH I WAS UNABLE TO DO. THE MICROWAVE WAS INSTALLED IN 1987 AND I BELIEVE THIS WAS THE FIRST TIME TO REPLACE THE BULBS. WHEN MY SON REMOVED THEM THE BULB WAS DIINTERGRATED. THAT'S HOW OLD THEY WERE. ONCE HE WAS ABLE TO REMOVE THE UNDERNEATH PLATE THE REPAIR WAS EASY EXCEPT FOR REMOVING THE OLD BULBS. I THINK THAT I COULD HAVE DONE IT MYSELF BUT HE WAS AVAILABLE AND I AM SURE IT WAS DONE MUCH BETTER. ALL IN ALL THE PARTS)BULBS) WERE CORRECT AND EVERYTHING IS WORKIIN FINE. THIS IS A GOOD PLACE TO ORDER REPLACEMENT PARTS. IN FACT I AM GOING TO ORDER A NEW CHARCOAL FILTER. HE TOOK THE LABEL OFF THE OLD ONE AND I AM ORDERING THE REPLACEMENT. AFTER ALL 1987 MAY HAVE BEEN A GOOD YEAR, BUT TIME FOR A NEW ONE.
MARY

BURNED OUT (and broken) LIGHT BULB

  • Customer: WILLIAM from BONITA SPRINGS FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
With many thanks to those who posted their experience and advice replacing the bulb, I was able to remove 5 of the 6 screws holding the underside panel and remove the socket which contained the broken off base of the bulb and extract it with needle-nose pliers. I had broken off the glass portion of the bulb trying to unscrew it due to the awkward contortion of my wrist-hand-fingers trying to grip the bulb inside the tight recess the bulb is mounted in. After concluding that I needed more information, I did a web search for 'Hotpoint RVM1435' and found helpful advice at partselect.com telling me to drop the bottom panel. Good call! Thanks everyone!

rotating plate broke

  • Customer: regina from weston FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
bought a replacement for it
All Instructions for the RVM1535DM2WW
76-90 of 183