Models > RVM1435WK01 > Instructions

RVM1435WK01 Hotpoint Microwave - Instructions

All installation instructions for RVM1435WK01 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RVM1435WK01
61-75 of 172
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken lens

  • Customer: Norman from Voorheesville NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
remove two screws bend out flaps remove broken glass install new glas bend flaps back to hold glass install two screws. Done.

Previoous glass lens was broken

  • Customer: Tommy from Santa clarita CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
This repair was easy and could be done by anyone. If you undertake to do this replacement, remember to slowly bend the medal tabs back that hold the lens. Handled roughly these tabs could break off.

This repair can be don in under 5 minutes, easily !!

microwave would not start

  • Customer: JULIA from JACKSONVILLE FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 7 people found this instruction helpful
took of cover removed switch and replaced with new one

Light bulb wouldn't light.

  • Customer: Steven from Marina Del Rey CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Removed difuser (one screw), removed old bulb, screwed in new bulb, replaced difuser.

Right hand surface lamp burned out. It apparently fald up and broke the glass cover. I wne on line when I found out the only local deaaler was some miles away and more expensive.

  • Customer: Leon F. from Brookline MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Simple. The parts came instantly. The glass was too big so I had it cut to size. I unscrewed the fixture with a screw driver replaced the bulb and slipped the glass cover into the frame and screwed the whole assembly in.

Light bulb burned out and assembly broke when trying to replace bulb

  • Customer: Jeanne from Kirkwood MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
I used the internet and your directions to complete the repair. It was easy!

Glass Carousel Cooking Tray Broke

  • Customer: Gary from Fernandina Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
I received the tray and place it in the microwave for a perfect fit. My wife is so happy.

light bulb burned out

  • Customer: Lois Jane from Fernley NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
took out several screws dropped down the panel under the microwave and unscrewed the bulb and put the new one in. It was a simple job.

Left light socket was damaged beyond repair

  • Customer: Kathleen from Streamwood IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
Handed the part to my son. He unscrewed 5 screws in the base of the microwave, it dropped down. The light mechanism was clearly in view. With the exception of some corrosion on the old piece, it was simple to remove and replace, put back together, screw back up and all worked fine.

Broken light socket

  • Customer: Richard from Batavia OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Turned the power to the unit off. Removed seven- (7) small screws from the base plate, not removing the rear screws. The plate dropped a few inches allowing me to get to the light socket.

I removed one- (1) screw that allowed the socket to be removed. I then detached the two- (2) electrical leads. I now installed the new socket, replacing the leads and the screw along with a new bulb. I pushed the bottom plate back into the up position and replaced the seven- (7) screws.

Turned the power back on and we were good to go.

Bulb was burnt out

  • Customer: Judy Ann from Fort Pierce FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Just unscrewed the screw holding the lens, unscrewed the bulb and put the new bulb in. Simple

Interior Light Out

  • Customer: Steven from Waldorf MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1 of 3 people found this instruction helpful
Removed Cover Plate,
Removed back cover
Bulb disintegrated removed base with pliers
Screwed in new lamp
Replaced cover
Done

Broken lens.

  • Customer: Gary from Warren MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Used a phillips head screw driver and loosened the lens frame under the microwave. Removed the broken lens and replaced it with the lens ordered. Put the lens frame back in place and secured it with the phillips head screw.

After closing door the display panel must be tapped on to keep the unit operating.

  • Customer: Paul from San Jose CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 12 people found this instruction helpful
The switches are not the problem! The problem is in the tolerences of the latch housing. I have ordered two new housings (Upper & Lower) and will see if the tolerences are closer. If not I will try epoxying a shim to the plate that operates the microswitches. The other option is to file the mounting slots of the housing to allow adjustment, which would be iffy,keeping them from moving with use. The exploded drawings really need to be clarified. The scale is way too small. It was extremely difficult to pick out the individual parts of the mechanisiam.

most of my touch pad buttons were not workin,fan/light

  • Customer: edward from chicago IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
after taking out about for screws or so i snapped out the panel put the new one in place and it works like new .mane the wife happy heck i even goe a kiss LOL
All Instructions for the RVM1435WK01
61-75 of 172