Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RVM1435BD001 > Instructions

RVM1435BD001 Hotpoint Microwave - Instructions

All installation instructions for RVM1435BD001 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RVM1435BD001
61-75 of 418
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Turntable no longer went around

  • Customer: Kent from Mesa, AZ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
I followed the instructions provided by others on-line who had done a similar repair. I removed a handful of screws, disconnected the wires from the old drive motor and connected them to the new drive, replaced the screws that held the drive motor in place, and those that held the bottom housing in place, and I was done. Literally took less than 10 minutes. If I had known earlier how easy it was, the microwave would have been fixed much earlier.

Turn table stoped functioning

  • Customer: Cody from Omaha, NE
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
Troubleshooting process:
Using a screw driver I opened the bottom of the unit using a Philips screwdriver and unhooked the drive motor electrical connector. Using a multimeter I checked to ensure power to the motor. This confirmed that the motor is bad and must be replaced.

Repair process:
After receiving new motor I removed the old motor and installed the new one using a Philips screwdriver and closed up the bottom cover.

It functioned good as new. Relatively cheap and very easy fix.

Door handle broken on microwave.

  • Customer: Shari from Sarasota, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
Fortunately I had my handyman here to repair a leak under my kitchen sink and asked him to replace the handle on my microwave. There were no instructions included with the handle but I had printed out descriptions from the web site of what others had done. He pried off the inside of the door which revealed two screws, which he removed. He then had to pry off another covering which revealed the other two screws that removed the handle. He attached the new handle and put the two parts that were pried off back on. It would not be an easy process for the ordinary householder and it would have been nice if detailed instructions had come with the handle (with pictures showing exactly which areas of the door needed to be removed). I was going to try the repair myself but am extremely glad my handyman was there as I probably would have ruined the microwave and would have had to purchase a new one. Kudos to my handyman.

Bulb burned ot

  • Customer: John from Fort Smith, AR
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 5 people found this instruction helpful
Un screwed the cover but when i tried to remove the bulb it was broken at the base. I disconnected the power and used neddle nosed pliers to remove the base

grinding of microwave turntable

  • Customer: William from Spring Hill, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
Ordering was simple Recieved part day after shipping. 3 days sooner than I expected.
Removed bottom panel. Removed 2 screws holding motor. Pulled out motor. Replaced with new motor. Reinstalled 2 screws, Put bottom panel back in place. The easiest repair I have ever done.
Have bookmarked your web page. When I need another repair part, this will be the only company I would consider doing business wth.

Sparked at the coupler, burnt

  • Customer: Robert from Bakersfield, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
Using the exploded parts view I removed three Philips screws from the lower plate (the screws are located on the front edge of the panel that holds the air filters). Slide the lower panel forward slightly and allow it to swing down. Remove the amphenol connector to the motor and hood lights by pressing the sides of the plastic clip and place the lower panel to one side out of the way. f you intend to clean the lower panel in a dishwasher remove all electrical components before doing so (bend back the clips holding the wires in place and remove the lamps, remove the Philips screws holding the lamp holders); note: these are the only screws with a short shoulder on them, make sure they go back in the same place to hold the lamp holder to prevent damage to the holder). Remove the Philips screw holding the turn table motor in place. Slide the entire motor assembly to one side to allow the motor shaft to slide off the coupler. With the oven door open, remove the old coupling by sliding it to one side to clear the retainer. Insert the new coupling and replace the motor making sure you align the motor shaft with the flat side of the coupling. If you have cleaned the lower assembly in the dishwasher or by hand make sure all parts are dry before reassembly (reinstall the lamp holders and the wiring assembly. Reconnect the amphenol connector (it can only plug in one way by nature of design). Slide the back of the lower assembly into the channel at the back of the oven and replace the three screws holding the lower panel in place.
Now you have saved your self the cost of a service call or possibly a new microwave you can use this as supporting evidence that you can afford the new 20" monitor for your PC. Test out the repair and make your spouse a cup of hot coffee or cocoa to brag on yourself and make your sales pitch.

Cooking tray drive motor did not work.

  • Customer: John from Muskego, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
Unpugged microwave. Removed the screws on the bottom cover of the micorwave. Unpugged drive motor and removed two screws from drive motor. Installed new motor and replaced the bottom cover, plugged in microwave . . . presto!

Installation was just as easy as numerous other customers indicated. Also, your service was as great as many other customers indicted . . . part was recieved in 2 business days. Thank you for great service and website.

Bulb was stuck in the lamp

  • Customer: lawrence from huntersville, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 5 people found this instruction helpful
First I removed the screws that were underneath the microwave. Once I did that I disconnected the wires to the bulbs and removed the screws that were attached to the holder lamp. replaced the parts and reversed the process. It went really smooth.

microwave dead

  • Customer: Jerry from Lillian, AL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 8 of 15 people found this instruction helpful
First, potatoe burned up in microwave. Microwave
was dead. Took off cover and found maintaince repair pamphlet in envelope. Schematic showed one shot thermostat for fire. Ordered thermostat from you and installed it. Works fine.

Cooktop light receptacle cracked

  • Customer: Ronald from Wood Dale, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
Remove screws holding bottom cover. Cover then swings down allowing access to the receptacles. Receptacles have a single screw attaching them to the appliance with a simple electrical plug supplying power. Very easy.

Cracked Door Handle

  • Customer: Brenda from St. Peters, MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
Removed Old Handle with minor difficulty, two screws came out easy other two had to drill out back plate to get to other two screws, after that, repair went fine.Took about an hour total time for repair, and sure saved alot of money!!

Glass Carousel Cooking Tray Broke

  • Customer: selwyn from inglewood, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 7 people found this instruction helpful
I replaced old tray with new. Received replacement part in two days. I was surprised at the quick response time. The part ordered was right the first time.

Glass carousel cooking tray shattered

  • Customer: Susan from Marco Island, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
It took less then 10 minutes to order. Received new part with 3 days

The cooking tray cracked.

  • Customer: William from Columbus, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
First I replaced the cracked cooking tray and I was done.

door handle broke ge nolonger stocked door or handle

  • Customer: robert from stamford, CT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 9 people found this instruction helpful
took a screw driver and pride off plastic on inside of door. be carfule not to break it. only one of two screws that go into handle were visable. had to drill a hole in metal braket to get at second screw. you can just bend the metal braket back inorder to use drill. bend it back when done. took off handle and replaced it. snapped plastic piece I took off back in place and finished.
ge told me i needed to replace whole door. which they nolonger stock and I could not find a whole door for my model on web. found handlw on this website and did it my self
All Instructions for the RVM1435BD001
61-75 of 418