Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RVM1325WW03

RVM1325WW03 Hotpoint Microwave - Overview

Get Parts and Repair Help for RVM1325WW03

If you know the microwave repair part you need, you can browse the list of all parts on the RVM1325WW03, or you can search by name or part description. You can also find your part by where it is located on the RVM1325WW03 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your microwave. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the RVM1325WW03

[Viewing 2 of 2]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$6.98

Light Bulb - 40W 130V

This light bulb is a 40 watt, 130-volt clear appliance light bulb that is manufactured to fit microwaves with small-base light bulb sockets. The light bulb illuminates the inside o...

$13.05

Light Socket - 250V 75W

This is a light bulb socket that is manufactured to fit a microwave appliance. The socket is meant to fit small-base light bulbs. The light bulb is not included with this part, so consider ordering the light bulb if necessary. You may need to replace this part if the existing socket is broken, cracked, or if light bulb is not turning on, and a new light bulb does not work. This is an electrical part so please be sure to disconnect power to your appliance before repair.

$21.50

Secondary Door Switch

The secondary door switch is a simple on/off mechanism that stops the microwave from operating when the door is open. The switch monitors the door latch position, and communicates ...

$10.61

Glass Light Lens

The microwave glass light lens protects the light bulb inside the appliance. It is clear in color and measures approximately 6-1/2 inches long, and 2-1/2 inches wide. You may notice that this part is cracked or broken and will need to be replaced. You will need to remove the screw holding the cover in place. Unhook the cover from the bottom panel. Bend the tabs up that are securing the old lens in place. The textured side should be facing up. Place the new lens into place and secure back into place.

$19.78

Monitor Door Switch

Unplug your microwave before attempting this repair. You will need to remove the grill, which is held into place by two screws at the top of the grill (open your microwave door bef...

$57.73

Aluminum Grease Filter

This aluminum filter collects grease particles in the air from cooking. Sold individually.

$22.20

Hood Damper Assembly

$3.29

Light Socket Screw

This screw is sold individually.

$25.77

THERMO SW-TCO SENSE TEMP

$8.57

Stirrer Cover

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

light worked, timer and control pad worked, but no turntable, no heat, no noises of any sort, just didn't start up

  • Customer: Marla from Arlington, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 216 of 246 people found this instruction helpful
Noted on partselect.com that someone else with this problem, found it to be secondary door switch. There are three door switches in this model, but online info noted that one of the three might feel "soft" (in my case, one switch clicked in a rather "jiggly" way, the other two were strong decisive clicks.) To access the door switches on this model was the ... read more

Light bulb out, tried to remove, lamp socket broke

  • Customer: Gene from Urbana, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 172 of 195 people found this instruction helpful
Above the stove mounted microwave. I dropped the lens cover from under the bulb and tried to remove the bulb. The bulb separated from the base. I tried to remove the base with a pliers and the lamp socket broke. I ordered the parts and dropped the bottom cover of the unit down (5 screws). Removed 1 screww from the lamp socket, unplugged the wires and took it... read more

Unit worked fine except it would not heat

  • Customer: Roy from Colorado Springs, CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 82 of 88 people found this instruction helpful
Had to take unit off wall and disassemble the main casing.then disconnected the wires from the magnetron.took the mounting nuts off but wasn't able to remove the magnetron until I loosened the transformer out of the way .Then it came out easy.Installed the magnetron ,tightened the nuts,installed the transformer back in, connected the the wires back on and... read more