Models > RVM1325WW02 > Instructions

RVM1325WW02 Hotpoint Microwave - Instructions

All installation instructions for RVM1325WW02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RVM1325WW02
76-90 of 162
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken light socket

  • Customer: Richard from Batavia OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Turned the power to the unit off. Removed seven- (7) small screws from the base plate, not removing the rear screws. The plate dropped a few inches allowing me to get to the light socket.

I removed one- (1) screw that allowed the socket to be removed. I then detached the two- (2) electrical leads. I now installed the new socket, replacing the leads and the screw along with a new bulb. I pushed the bottom plate back into the up position and replaced the seven- (7) screws.

Turned the power back on and we were good to go.

Bulb was burnt out

  • Customer: Judy Ann from Fort Pierce FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Just unscrewed the screw holding the lens, unscrewed the bulb and put the new bulb in. Simple

Interior Light Out

  • Customer: Steven from Waldorf MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1 of 3 people found this instruction helpful
Removed Cover Plate,
Removed back cover
Bulb disintegrated removed base with pliers
Screwed in new lamp
Replaced cover
Done

Broken lens.

  • Customer: Gary from Warren MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Used a phillips head screw driver and loosened the lens frame under the microwave. Removed the broken lens and replaced it with the lens ordered. Put the lens frame back in place and secured it with the phillips head screw.

Broken Microwave Door Handle

  • Customer: Charles from Westmont NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 4 people found this instruction helpful
The part arrived very quickly - within three days of my order. It was a little challenging to get the broken handle off - you have to hold the plastic screw inserts with pliers or another screwdriver to prevent the screws from just spinning in place. Once secured from spinning, I was able to remove the two screws that attach the handle to the microwave door. The new part went on easily, but the fit of the new handle was snug and the screws a little difficult to drive. It helps if you push on the handle to keep it tight as you drive the screws. The entire repair was completed within five minutes and the microwave was "back in business". This repair can be easily completed by someone with little mechanical ability.

The bulbs burned out, the glass lens cracked and the light socket broke when trying to remove the bulb

  • Customer: Warren from Council Bluffs IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Replaced the sockets, lens and bulbs. The first time the new bulb was touching the lens and the heat broke the lens and burnt out the bulb. The second time I adjusted the socket so that the bulb does not touch the lens.

Impressed by how quickly the parts arrived after the order was submitted. Two days.

Thank you.

Broken light lense

  • Customer: George from Marana AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed one screw, installed new lense in lense frame, rescrewed. Done.

bulb burned out -cracked holder lamp

  • Customer: Terry from Justice IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
pluged wires back on ,placed lamp holder and bulb back and replaced screws

light lens broke a couple of years ago

  • Customer: KAREN from MANSFIELD MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
unscrewed the screw, pried up metal tabs that hold in light lens. took out broken pieces, slid in new light lens re-secured tabs with fingers, screwed in the screw again.

light out over stove

  • Customer: virginia from hilton head island SC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
so easy, but how do i turn light off?

Part recieved next day. thanks so much

UNDERNEATH LIGHT ON MICROWAVE WOULD NOT COME ON.

  • Customer: MARY from PLYMOUTH MA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
MY SON=LAW DID REPAIR BECAUSE i AM ELDERLY AND IT WAS NECESARY TO REMOVE THE BOTTOM PLATE OF THE MICROWAVE WHICH I WAS UNABLE TO DO. THE MICROWAVE WAS INSTALLED IN 1987 AND I BELIEVE THIS WAS THE FIRST TIME TO REPLACE THE BULBS. WHEN MY SON REMOVED THEM THE BULB WAS DIINTERGRATED. THAT'S HOW OLD THEY WERE. ONCE HE WAS ABLE TO REMOVE THE UNDERNEATH PLATE THE REPAIR WAS EASY EXCEPT FOR REMOVING THE OLD BULBS. I THINK THAT I COULD HAVE DONE IT MYSELF BUT HE WAS AVAILABLE AND I AM SURE IT WAS DONE MUCH BETTER. ALL IN ALL THE PARTS)BULBS) WERE CORRECT AND EVERYTHING IS WORKIIN FINE. THIS IS A GOOD PLACE TO ORDER REPLACEMENT PARTS. IN FACT I AM GOING TO ORDER A NEW CHARCOAL FILTER. HE TOOK THE LABEL OFF THE OLD ONE AND I AM ORDERING THE REPLACEMENT. AFTER ALL 1987 MAY HAVE BEEN A GOOD YEAR, BUT TIME FOR A NEW ONE.
MARY

Lost screws for the covers on the lights over the cook-top

  • Customer: Geraldine from Clearwater FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Placed the screws in the proper areas, used the screw driver to tighten down and I was in business with light to spare. I am happy to have found the proper screws.
Thank you.

time would count down but unit would not run & heat.

  • Customer: Bill from Shawnee OK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
remove cover, unplug secondary door switch (top switch)
remove switch from holder, install new switch, plug in wires, replace cover, very easy. door switches are a common problem
with microwave ovens.

Light bulb was burnt out and lens was broken

  • Customer: Andrew from Bolton CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Unscrewed the lens, it hinged down, then I could remove the frame. Pulled old bulb out and replaced with new one. Replaced broken glass in frame. Reset hinge into the holes and swung it up into place. Screwed it in.

Very easy!

Bulb broke in light socket

  • Customer: Douglas from Ludington MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
Tyring to get bulb out i ruined the light socket. Unscrewed the bottom cover of microware. Took out screw holding light socket, removed wires to socket with pliers, intsalled new socket. It was a piece of cake and the part was a perfect match.
All Instructions for the RVM1325WW02
76-90 of 162