RVM1325WW004 Hotpoint Microwave - Instructions

Removed 5 screws from the bottom of the over the range microwave to expose the light sockets. Removed the 1 screw holding the socket, disconnected the wires. Attached the wires to the new socket, Put in the bulb, reattached it with the screw. Repeated on the other light... It took about 20 minutes and now the lights work just like they should :)

The order was easy and promptly received. I lowered the cover by removing retainer screws underneath. Simply lowered it and removed the broken glass and replaced it. The bulb was broken and the base of it was stuck in the socket. I didn't bother to remove it because the socket was brittle. I disconnected the socket by unplugging the wires, removing the retainer screws,and removing it. I replaced it with the new one. Screwed in the bulb. I replaced the cover and it was done. Ps: I used an Hitachi cordless screwdriver, which greatly helped when doing this alone.

thank you very much.

First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.

I thought I could just unscrew the bulbs in the SpacemakerXL Microwave Oven. The bulbs melted into the bulb socket so every attempt to unscrew the bulb with pliers just broke the socket. So I took out the few screws holding up the bottom panel(with the bulbs and filters). I unplugged the electrical connection and took out the sockets but I used PAM Cooking oil on the electrical connections plugging into the sockets to avoid pulling the wire holders from the connection. Replacing both bulbs and the sockets at the same time makes sense since the heat from the stove melts the bulbs in the socket.

I first read where someone had the same problem. Their solution was a burned-out fuse. I ordered a new fuse...installed it and that did not solve my problem. I revisted PartSelect and read how Marla (from Arlington, TX)solved her problem. I purchased a secondary switch and when it arrived, I made a copy of Marla's instructions and followed them to the letter. I installed the new secondary switch into the secondary space, put everything back together and the oven STILL DID NOT WORK. I had to take the latching panel apart again and test each switch to see if there was another bad one. I found that the third switch was burned out. So I took the new switch out of the second slot and installed it into the third slot. I tested the switches before reinstalling the latching panel. This time everything worked. So I put everything back together, reinstalled the microwave on the wall, tested it again, and everything worked perfectly.

simply to install new bulb. Unscrewed the under the microwave lamp door with a screwdriver. Inserted new bulb into socket. good to go

I replaced the cover just fine but i think a sensor went bad

Changing 2 lightbulbs is NOT ROCKRT SCIENCE. With a screw-driver, remove the under MW light lens, unscrew the 2 burned out light bulbs, and replace with 2 new quality light bulbs. Test out that both are lite and working as they should, replace the lens and you are done, Until you find out one of the new (made in Chins) light bulbs is burned out after about 6 hours of being lite, call the parts phonr number and order a new replace bulb.

Went online to get a brief description of the complexity of the repair.Once I ascertained that it was an easy repair I ordered the part, dis-assembled the door, removed the damaged part and when the new part arrived I installed it.Total time was well under 30 minutes and most of it was trying to go slow and not snap the plastic housing on the door.

Replace the fuses

simply unscrewed protective lens cover, and swapped bulbs--these bulbs are great--last for years

Removed the above stove microhood. Removed the side panels & the top panel. Diode located on right hand side of microwave. Removed with screwdriver & replaced new diode. It's best to get the microwave schematic online to pinpoint location of the part.

I removed light bulb cover shield,took out defective bulbs and replaced with new ones. 5minute repair

Removed the microwave with the buit in housing from the cabinet. Removed microwave from built in housing. Removed outer cabinet giving access to remove control panel and smart board where switches are located. Removed control panel to get to smartboard. Removed smart board after disconnecting a few wires to allow easy removal. Individually removed and then tested each switch using multimeter. Found seondary Door Switch (bottom of smart board) operation to be intermittent (switch trip button extremely loose and rattle inside this particular switch) Ordered replacement part which came very quickly on standard shipping order. Put new switch on smart board and remounted, reinstalled control panel and reconnected various wire connectors previously disconnected. Then plugged in oven and tested for opertation - didn't work at all! But, after bleeding off capacior charge by removing connectors and discharging capacitor to ground, then reassembling control board and smart board into oven, then trying agian, it has worked perfectly ever since. Do not understand why capacitor disconnect/discharge was required but suspect this reset the control electronics. Easy fix and hope to get another 12 years out of this appliance which is used multiple times every day. Also have two other identical micorwave ovens, one is 20 years old, but these get used relatively infrequently.