Models > RV15EFREW02 > Instructions

RV15EFREW02 Roper Freezer - Instructions

All installation instructions for RV15EFREW02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the freezer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RV15EFREW02
1-10 of 10
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 12 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

gasket had harden. frost was building up quickly

  • Customer: LESLIE from TAPPAHANNOCK VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 10 of 13 people found this instruction helpful
the gasket peels back to reveal the approx 20 screwsholding gasket and door shelves. removed these. removed old gasket from door panel. new gasket needs to be stretched to get on door panel. align screw holes in door panel with screw holes in gasket. attached back to freezer door. this gasket did not seal securely when closing door. this gasket was installed on a cold day in a garage and may become more flexible as it warms up.

Refrigerator stop working

  • Customer: SAL from UPLAND CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 11 of 18 people found this instruction helpful
First I removed the relay and over load and exam. Saw that the relay was burnt. Before I order the part I check to see if the compressor was still working by jumping the common start and run terminals.It did. I also checked the start capacitor with a capacitor tester it was good. I than order the part which came the very next day.Installed the part

Both outside door handles turned very beige

  • Customer: Howard from Boynton Beach FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 4 of 11 people found this instruction helpful
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

The compressor did not kick in....

  • Customer: Mike from Sherman CT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 3 of 10 people found this instruction helpful
The repair was easy......however I had no help to identify the problem and after I did I had no description or schematic of how to connect the parts. The old defective part was not identical to the new one. some written material would have been helpful.
Z. Benedek

Cimpressor would not start

  • Customer: Oliver from Madison AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 8 people found this instruction helpful
Checked compressor with amp meter, and found it was not running, found Overload Switch bad.
When removing old switch watch carefully which lug you move wires from, so you will know which
lug to put the new switch on.

BE SURE YOU KNOW SOMETHING ABOUT
ELECTRICITY!!

After Hurricane Irene refrigeration compressore did not start

  • Customer: Bobby from New Bern NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 3 people found this instruction helpful
Followed the directions. Installation was quick. Took loner to put the covers back on and push the applicance back in position than the repair.

change relay

  • Customer: Robert from Boxborough MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 10 people found this instruction helpful
unplugged relay and plugged in

Starting relay went out

  • Customer: George from Conroe TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 13 people found this instruction helpful
Forty years ago I serviced air conditioners and all kinds of refrigeration. At that time starting relays were electro mechanical, I hadn’t looked under a refrigerator in a lot of years and was surprised to find out that the new relays were solid state. The defective one had a bunch of broken pieces floating around in the case. I jury rigged a starting cord and confirmed that the compressor would start and looked at running current for thirty or so seconds. I ordered a new relay kit and it worked just right. I’m seventy five years old and it takes me longer to get up off the floor than it took to replace the parts. Your delivery was first rate the parts got here before I finished doing the paint touch-up on the door under the ice maker/water dispenser. Fed ex was easily three to five days faster than the brown truck.

broken left arm to hold rack in

  • Customer: Roy L from Layton UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Just put the two screw back in that i had removed.
All Instructions for the RV15EFREW02
1-10 of 10