Models > RUD5750DB3 > Instructions

RUD5750DB3 Roper Dishwasher - Instructions

All installation instructions for RUD5750DB3 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RUD5750DB3
166-180 of 190
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Top dish rack detached from roller

  • Customer: Robert from DeSoto TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed the rack end stop by pressing the clip together using hand; removed the broken roller and rack support clip by snapping away from the rack. It was literally a snap to remove and replace. Very easy to do, my 12 year son could easily replace the roller assembly.

Soap Dispenser Cover would not open all the way

  • Customer: Dwight from winona MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed dispenser cover by using flat screwdriver, then slid the lid hinge pin and lid spring by pushing the lid hinge pin out on the silverware trade side. Then I put the lid hinge pin back into its place, once started I put the lid hinge spring on the lid hinge pin and pushed the pin into place, used flat screwdriver to put the lid spring in place, then I snapped the soap dispenser cover on the lid hinge pin. It took me about 5 minutes to remove and replace these parts, a very easy repair.

Leaking during cycle

  • Customer: Randy from Soldotna AK
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced the seal, still leaked. Once I noticed that it was only leaking from the left side, we did a Google search to find that the screen in the upper left of the door could be the issue, causing back pressure. Once the screen was cleaned, no more leaks.

Soap dispenser not opening

  • Customer: Leslie from Brooksville FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took inside door panel off. replaced spring that opens soap dispenser lid during cycle. Put inside panel back on. Works fine now.

QUICK AND EASY

  • Customer: STEVE from WHITE PINE TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
OPEN BOX, REMOVE REPLACEMENT PART, 5 MINUTES LATER ITS DONE. MOST OF THAT 5 MINUTES WAS CLEANING ON THE DISHWASHER. THANKS.

Not draining completely

  • Customer: Sallie from Ahwahnee CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug dishwasher from electrical, water supply and drain hose. Pull dishwasher out from under cabinet. Unscrew water whirler from inside washer, then remove motor. Remove black boot from motor. Unscrew keeper from impellor housing. And you are there! Pull impellor off motor shaft. Replace seal first, then replace impellor. So easy this girl did it. But, this girl also does small engine repair!

Water leaking into empty dishwasher.

  • Customer: Albert from High Point NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
After emptying the dishwasher the bottom had no water in it. A few hours later there was water in bottom. This told me the inlet valve was leaking. I took the bottom kick plate panels off. Directly in front on left side was the water inlet valve. Remove mounting screw, disconnect electrical connection, the water feed and discharge hose and remove valve. Install new valve. 100% DONE! Reinstall front panels after checking for leaks. At 71 years of age my typical 20 minute job actually took less time.

The soap dispenser lid spring was broken.

  • Customer: craig from eighty four PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
I watched the video, which was very good, and did the repair. It took about 10 minutes. Most of that was watching the video. EXCELLENT VIDEO!

Heating element would not heat

  • Customer: Jim from Republic MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I watched the video, read all the post, they all said change the heater. So I did. Only there is a little fuse at the back of the unit that also goes bad and that was my issue. Have it ordered and will be going soon. That said, Part Select made finding and getting my parts a breeze!

Water leaking from door

  • Customer: Kenneth from East Providence RI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just followed the online instructions. I used white vinegar to clean any residue first. So easy.

The plastic brackets that hold the screw against the frame had broken

  • Customer: Rahul from Irvine CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove the Access Panel retainer from top of the panel. Then remove the Access Panel and the Spacer Panel from the front. Then remove the Extension from the bottom. This step was kind of difficult, I ended up bending the plastic bracket on the pane since I was going to throw it away anyway. Install all the parts onto the new panel in the reverse order. Screw the panel back on to the dishwasher.

water leaking from bottom of door

  • Customer: Mary Ann from Menahga MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
removed the 2 water deflector and slipped the new ones in , in place.. very easy to do but it didn't seem to stop the leak so ordered the door gasket

The part had broken, causing the upper rack to droop.

  • Customer: Jan from Bend OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The repair was so easy it was ridiculous...simply removed the end cap on the front of the roller assembly, took old one out, added new one and then put the end cap back on! Done in about 2 minutes!

Leaking where motor drive shaft enters pump

  • Customer: Steven from Woodstock IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove lower rack in dishwasher, remove dishwasher, lay dishwasher on it's back, remove and replace motor and pump.Install new impellar with new seal. reconnect water, electrical and drain hose. Easy Peasy

Broken Hinge Lid Pin and Lid Spring

  • Customer: Jan from Chatsworth CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video's from Parts Select and it took me less than 3 minutes to replace these parts. I did find it easier to use a screwdriver to lift the u shape of the spring over the detergent cup as the pliers tended to pull on the spring too much. Couldn't have been easier or faster, awesome!
All Instructions for the RUD5750DB3
166-180 of 190