RUD5750DB1 Roper Dishwasher - Instructions

Washed the edges good and clean to remove old tape that was holding the old panels. Slid in the new ones and found that the retaining strip would not work without replacing the inner strip. I didn't want to order this $53 dollar plastic strip so I squeezed a couple of rubber pieces into the bottom of the side edges to hold the top panel. Placed the retaining strip in place and used a long strip of black duct tape at this bottom edge to hold it all. It works and the new panels make the dish washer look close to new,the black duct tape hardly shows. This works good for my 10+ year old dishwasher until it is replaced with one that has a better door design.

The easiest way to change this out is to remove the access panel(like the one you purchased) and the metal brace that supports it to the bottom metal access panel. To do this, REMOVE the screws in between the door and access panel. Step 2: LOOSEN screws that connect the metal braces together. You do not need to remove them completely as the middle brace slides up. You should now have the panel and brace together in your hands. Step 3: Using a flat screw driver pry (and I mean pry!) the retainers out of the catch. At this point breaking the old plastic is a better option than bending the metal! Once removed, your ready to swap out the front cover of the panels and put'er back!! Good Luck!

i determined that the impeller was not free. ordered and installed an impeller kit which included a new bushing, which was the culprit. it was a fairly simple fix, needing only to remove the pump housing from the back of the motor. access to the impeller was by removing the screw-in, x shaped connection on the back side of the impeller housing. runs like new again. the fix was far less expensive than a new washer.

My husband did the repair. He sucked the water out with the wet/dry vac. Layed it over on the front and removed the pump motor and replaced it.

Turned off electricity. Removed the interior door cover. Removed door switch. Replaced switches & reversed process. By the way - I am a woman & diagnosised, ordered part & fixed it myself - I have no experience in this field. THANKS for all your information on your site.

This is the second time I have replaced a rack. You just pop on the new rollers and you're good to go!

but the pin in and add the pin though the 2 tabs close door on it open it up move the springs backwards to the door

All I had to do was remove old door panel and retainer and I replaced with the new.
PartSelect were great. I highly recommend you guys.

removed two hose clamps and old hose. slid new hose on existing fittings on dishwasher drain and disposal and tightened hose clamps. Turned it on for test run.

Pulled off the bottom trim, slid the old panel off and put the new panel on. Then popped back on the bottom trim.

Had to be careful positioning the spring without breaking the hinge pin. Requires a certain amount of patience.

remove star screws holding inside door panel. remove plastic cover that protects latch assembly. hook one end of spring on stationary pin on inside of slider bar. Hook other end of spring on pin on slider bar. replace cover and door panel.

Replaced door gasget took 5 minutes tops. Ran cycle and still had leak. Called local repair person. After thoroughly checking out the dishwasher and running soapless cycle determined problem to be soap build up over time. He ran a commercial cleaner through a complete pots and pan cycle. No more suds and no more leak repair complete. Did not actually need door gagset but it was super easy to change and delivery service was great.

Replaced the impeller using the kit. Had to brake the impeller since it was stocked due to rust.

I watched the video link sent in an email and followed exactly what they did in the video. I removed the star head screws holding the door liner in place. Then removed the protective cover on the inside. I disengaged the component holding the latch in place. I replace the component that holds the latch in place and then snapped the new latch in place. I turned the dishwasher dial until the prongs were fully retracted. I replace the protective cover and then put the door cover back in place. I initially only placed the left bottom star head screw until I was sure that the latch was going to release. I tested that it was working properly by slowly turning the dial on the dishwasher control. Once I knew it was working I replaced the rest of the screws.