Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RUD3000GB0 > Instructions

RUD3000GB0 Roper Dishwasher - Instructions

All installation instructions for RUD3000GB0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RUD3000GB0
76-90 of 176
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Upper dishrack needed replaced

  • Customer: Scott from Wichita, KS
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 3 of 8 people found this instruction helpful
I removed the upper dishrack easily by removing the end clips and sliding the tray out. Removal of the revolving sprayer was easy as it just clipped on to the bottom of the rack. The rack was not the rack that was ordered and I was informed that this was the correct rack for the dishwasher even though the description and picture was different that what I received. There were no instructions with the rack to explain how to attach the "flaps" that can go over lightweight dishes to keep them from flipping. Every way I tried to attach the flaps did not work. When I was able to attach one it would pop off if I raised the flap to place a dish underneath it. I finally gave up on the flaps and reinserted the rack onto the rails and put the end clips back in place. The rack works fine other than it is not the one that was described and was not the rack that I wanted.

my old lady bumped the side of the top rack with her ass

  • Customer: GARY from FINDLAY, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 5 people found this instruction helpful
broke the wheel in the top rack and just popped out the old and popped in the new and the little lady is happy again.

changing a damaged door panel insert

  • Customer: Constance from Sonoma, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
I needed to cut 1/4inch off the panel and unscrew the side piece which held it in place....
insert the new piece and put back the 3 screws. Done!

broken roller assemblies

  • Customer: WALTER from DES MOINES, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Just popped off the old ones and popped on the new ones. Only thing thiat might have been helpful would have been a diagram of where the roller assemblies should be located.

worn and rusted lower dishrack

  • Customer: Greg from Royal Oak, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
First, I checked the ripped box for damage to the dishrack. Fortunately, there was none. Then I looked for the instruction booklet. Unfortunately, there was none. And the parts bag was ripped and I did not know what was supposed to be in it. So, I rechecked the photo of the dishrack on the website and found that either parts were missing or the dishrack was different than illistrated. After a few moments of thought, I realized the latter was the case. I then figured I would have to use some deep thought to do the installation since neither the missing instruction booklet nor the unzoomable photo would help. So, I pulled out the tall thin thingamabob from the old dishrack and put it in the new one though it did not secure as tightly. Then I put the wheel units on just like the old one. What I could not immediately figure out was where the collapsible rack row was mounted. I eventually realized that the rod went into a hole in the wheel units and the latch mounted above one unit. I still have no idea where the two other tan clips go. Though the dishrack is different and thus requires different science to fill it, it appears to do the job.

Thanks for asking.

By the way, it was not blue.

Cap did not stay in the hole any longer.....was melted

  • Customer: Debra from York, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 5 people found this instruction helpful
Just screwed the new cap in. This PartSelect was AWESOME. So easy. Lighting fast shipping !!!!

water leaking from door

  • Customer: tim from loganville, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
The whole job took less than 5 minutes...no tools were needed The diagnosis was right on the money

Small leak in bottom right corner of dishwaher

  • Customer: Roger from Duluth, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Took off bottom plate (2 screws) and ran unit to ensure where leak is from....it appears to be the door seal. Pulled out old seal with fingers and replaced door seal, ensuring its properly "fitted"..ran unit, no leaks, put bottom plate back on

4 broken wheel assemblies on upper rack

  • Customer: Jeffrey from Little Egg Harbor, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
Snapped them in place....2 minutes....ordered the parts 2PM on a friday and they arrived 11AM Saturday...couldn't believe it! Thanks!

Water leaking from front door of dishwasher

  • Customer: Gregory from North Port, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Took less than 5 minutes. Pried edge of old door seal out with a flathead screwdriver, then slowly pulled out old seal. Thoroughly cleaned area for new seal with rubbing alcohol, inserted new seal and trimmed the end to fit just right. Presto, no leaks whatsoever!

pump seal and impeller

  • Customer: David from Lisbon, IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 1 of 3 people found this instruction helpful
had to replace the insides of a leaky pump

Tines where falling off old rack

  • Customer: RONALD from EAST GREENWICH, RI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 12 people found this instruction helpful
The dishwasher is 25 years old. Ordering the part was simple. Very good web site and user friendly. The shipment and delivery perfect. Part arrived as predicted. Tracking delivery was also perfect. Part was exactly what I needed. The only hitch was that there were no instructions for assembly, not even a drawing of the assembly to give a hint as how to assemble. Therefiore assembly took longer than it should have. However the diswasher is back in operation and I am pleased with the results.

slow leak at motor/pump interface

  • Customer: Donald from Webster Groves, MO
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 1 of 3 people found this instruction helpful
Got parts breakdown online, took pump assy apart, ordered new parts, replaced bad parts, put pump assy and dishwasher back together, piece of cake, no problems.

Dishrack Tines were breaking off due to age

  • Customer: Keith from Dayton, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
The rack came with pictorial instructions which were fairly veg, however they were to the point. The wheels snapped into place easily, and the center water transfer tube twisted off the old one and twisted on the new one just fine. It is a very good idea to keep the old one out to look at as a guide. There were no instructions on how to remove the transfer tube, I was lucky to have already worked on these before. After that it fits and works just peachy.

door seal leaked steam

  • Customer: BRIAN from GOWANDA, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
It was a very simple repair. I removed the old door seal out of the track and installed the new seal.
All Instructions for the RUD3000GB0
76-90 of 176