RUD3000GB0 Roper Dishwasher - Instructions

I paid a repairman over $100 to tell me he could find nothing wrong with my leaking dishwasher (it didn't leak when he ran it). I narrowed down the problem to a missing water deflector, but decided to replace the door gasket as well. It took less than 5 minutes to do the job. The only tool I used was a pair of needle-nose pliers to grasp the old door gasket and get it coming out of the groove. Thanks PARTSELECT for super-fast shipping and a website that is easy to navigate. I'll be coming back, 'cause all of my appliances are getting some age on them!

The video was of great help. One area that gave me grief was placing the small part with points under the plastic mechanism in the door. I tried to push the points into the open slot. After watching the movie a few more times I was trying to put the part in backwards. A little more explanation at this point in the video would have been a tremendous help. Otherwise, thank you for the video.

Bought a house and with it can an old whirlpool dishwasher in where the soap dispenser lid would latch, as the latch itself was gone. Ordered the latch from part select and used the installation video to switch the latch out. Only problem I came across was that the torx screws at top of he door were free spinning. Ended up using a flat head for leverage to finally get the screws out. Everything works perfectly for once.

I used a screwdriver as a wedge to remove the existing panel and inserted the new black panel into the groves located on the front of the dishwasher. Installation was easy because I followed the instructions from the website. Piece of cake. Less than 2 mins.

The repair was very simple. Simply pull the dishwasher out far enough to access the springs, remove the old with pliers and install the new springs in the same spot as the old ones.

Made sure the power and water were not connected to the dishwasher. Removed the bottom panel. Unhooked the old part. Put some plumber's tape around the threads, hooked it all back up. Runs just as good.

took out old door gasket replaced it with new, also cleaned the air vent at top of door. Ordered shield at same time but didn't use it, so returned it, haven't received refund yet, but expect one soon. Dishwasher works great and NO leaks. Wonderful website

Followed vidio instructionson web site. Quick easy fix

The repair man from a serve we use, look up on how to replace the door gasket. Washing hands, do not stretch, and tap rubber into place. No more leaks.

Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install

slid the pin into place, noting correct position of spring, backed hinge pieces with screwdriver and pressed door into place. Your video made it easier than ever. ( My 2nd time replacing the pin. ) Great repair experience.

The top of the latch was broken on I had to push the plunger back through the mounting to get it out. ai had to pull the whole assembly apart to get the locking nut out. i remove the latch assy and took about 10 minutes to figure out how to put it back together. Changing it with the help of the video wasn't hard but confusing at times. Thanks for the video.

Removed dispenser cover by using flat screwdriver, then slid the lid hinge pin and lid spring by pushing the lid hinge pin out on the silverware trade side. Then I put the lid hinge pin back into its place, once started I put the lid hinge spring on the lid hinge pin and pushed the pin into place, used flat screwdriver to put the lid spring in place, then I snapped the soap dispenser cover on the lid hinge pin. It took me about 5 minutes to remove and replace these parts, a very easy repair.

I replaced the seal, still leaked. Once I noticed that it was only leaking from the left side, we did a Google search to find that the screen in the upper left of the door could be the issue, causing back pressure. Once the screen was cleaned, no more leaks.

Took inside door panel off. replaced spring that opens soap dispenser lid during cycle. Put inside panel back on. Works fine now.