Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RT25BKXAW00

RT25BKXAW00 Roper Refrigerator - Overview

Get Parts and Repair Help for RT25BKXAW00

If you know the refrigerator repair part you need, you can browse the list of all parts on the RT25BKXAW00, or you can search by name or part description. You can also find your part by where it is located on the RT25BKXAW00 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for RT25BKXAW00 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.88

Light Bulb - 40W

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...

$11.11

Light Rocker Switch

This light rocker light switch is used in a number of household appliances. It is most often found in refrigerators and freezers. This is a simple mechanism that helps turn the light in your appliance on and off. If the door of your appliance is open the light should be on, and if the door is closed the light should be off. Your appliance door is opened and closed frequently, meaning the mechanism may wear out over time. It is not uncommon that this part will need to be replaced. You may need a putty knife to release the mounting tab and remove the faulty rocker switch. To install the new one, simply attach the wires and snap it into place in the liner of your refrigerator or freezer.

$6.49

Door Shelf End Cap Kit

This door shelf end cap kit contains two white end caps, two adhesive strips, and an instructions sheet. Each end cap can be used as either for the left side or the right side.

$5.21

Icemaker Water Fill Tube Kit

The icemaker water fill tube provides water to the icemaker so it can produce ice and dispense water. If you notice that your ice maker is not making or dispensing ice, or is leaking, you may need to replace the water fill tube. This water fill tube kit comes with a fill tube and a compression nut. This part is made of white plastic and is approximately 10 inches in length. The ice maker water fill tube is in the rear of the fridge. To complete this repair, you will need a 1/4 inch nut driver and a utility knife. Before beginning this repair, you may want to disconnect the water and power supply to the refrigerator.

$37.73

Condenser Fan Motor Kit

This condenser fan motor kit is designed for use with refrigerators. This fan draws air through the condenser coils and over the compressor. It does this with the goal of cooling t...

$20.01

Bimetal Defrost Thermostat

This clip-on thermostat will sense the temperature increase in the evaporator during the defrost cycle and will cycle the defrost heater off after the ice or frost is melted.

$26.40

Shelf Support Stud

This is a 12 piece kit.

$3.02

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

$15.95

Switch, Plunger Grid/Light

The purpose of the light switch in your refrigerator is to automatically turn on the light when the door is opened. If the light does not come on automatically when you open the do...

$2.96

Screw

Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 131 of 141 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more

Broken elbow on icemaker water fill tube.

  • Customer: Charles from Orland Hills, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 108 of 119 people found this instruction helpful
Removed 2 screws holding water fill tube to rear of refrigerator and pulled out, matched old part with new to make sure of proper match. Guide new fill tube thru hole, making sure it is aligned with slot in ice cube tray on inside of freezer. Install new plastic line from water pump outlet to water fill tube, check for leaks, job done. read more

Unit very noisy and freezer too warm

  • Customer: Michael from Churchville, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 73 of 77 people found this instruction helpful
First I removed the racks in the freezer. The rack supports on the sides lift off without tools. The evaporator cover is at the back of the freezer. 4 phillips head screws. The cover lifts up then forward to expose the evaporator, evaporator fan and duct. The duct is held by 3 hex head screws. The evaporator fan is attached to the duct with a wiring pigtail ... read more