Models > RT18BKXKQ02 > Instructions

RT18BKXKQ02 Roper Refrigerator - Instructions

All installation instructions for RT18BKXKQ02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RT18BKXKQ02
31-45 of 133
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The Freezer defrosted and everything on the top and the bottom spoiled

  • Customer: Jorge from Miami FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 5 of 8 people found this instruction helpful
i had used your web site before and i read several problems that your readers had. i went to the back of the unit, removed the bottom cover and right there the i found the run capacitor and i chaged it. since i had only ordered this part to save money i went back and ordered the Start Device which when i took it off it was completely burned. the replacement part came labeled with 2 different compressor #, so i picked the one that i had and unpluged each wire. the part may differ from the one that it's in the unit but it worked when i pluged everything back on. it also helps to take a picture of everything before removing the wires in case you have to leave it and come back later. i hope to use this refrigerator another 10 years. thank you all for your help.

Fill tube on the icemaker was leaking.Looked at sears repair parts list and part was $62. I found the same part here for $4.99. Very easy to just remove the old part and replace it with the new. I also received the part in two days. Amazing!!!!

  • Customer: Walton from Woodland PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 3 of 3 people found this instruction helpful
Simlpy removed two screws to remove the old part. replaced the new part and put the two screws in. Job finished.

Overload was open

  • Customer: richard from galena KS
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
New part was similar, except contact blade was for a full 1/4", my model utilizes 1/8". So I cut the blade in half with a hacksaw, filed off the rough edges and reassemblied the connector; attached it to the compressor
Now being a retired electronic engineer; who's great idea was it to hide a klixon inside the connector?

All three lights are not working...lights are off but refrigerator still cooling. Also, the control box not lit up to show the temparture for freezer and refrigerator

  • Customer: Antonio from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 7 people found this instruction helpful
Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

Water was running onto the floor

  • Customer: Charles from Milton FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 4 of 7 people found this instruction helpful
I called Parts Select and the representitive faxed me a picture of the refrigerator that came with a home purchase. With the help of the parts breakdown and the Parts Select phone rep to figure out the part I was missing was the evaporator pan. I ordered the evaporator pan and it arrived the next day. I installed the pan and was back in business.

Water fill tube broken

  • Customer: Jeffrey from Monroe MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
removed two screws and pulled part out of the unit. The local appliance store said they needed model and part # to try to identify and order the part. Found part select online, found the part immediately, ordered the part for $4.50 or so. Part was delivered in 2 days! Very easy installation and the part works perfectly. Thanks so much!

Installing old ice maker in new freezer

  • Customer: Harry from Ten Mile TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
I was able to transfer my old ice maker from my old Roper Refrigerator/Freezer into my new Whirlpool Sidekick Freezer. Everything transferred directly except for the water fill tube. I ordered one on line and simply cut it to the right length, removed the cover plate inside the freezer compartment and the little sticker from the outside. Inserted tube and fastened in place with two screws (not provided but was able to use the screws that were in the holes inside the freezer before the ice maker went in. Works great. By not buying the ice maker with the freezer I saved a hundred bucks or so.

The switch broke...absolutely fell apart.

  • Customer: Duncan from Metairie LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service!
Duncan Quaid

Freezer icing up

  • Customer: phil from sioux falls SD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 8 people found this instruction helpful
Freezer was running for extremely long periods I noticed and not doing a great job of cooling the fridge.I assumed it was in need of a defrosting so I took the panel off to take a look.
The whole radiator was covered with ice.I could see the defrost thermostat was half way popped out of its casing at a 45 degree angle.
I just had to cut the 2 wires to the defrost thermostat and wire nut the new one in.Very easy fix as the part just clips on radiator.

There was no light on in refrig area

  • Customer: Lori from Chuluota FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 8 people found this instruction helpful
Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

Broken filler tube at threaded connection

  • Customer: Matthew from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
After discovering that the water noise was coming from the rear of the refridgerator upon pulling it foward I discivered the connection line had broken. So i got a phillips screw driver and removed the the two mounting screws and saw it was one piece. I easliy found the part on PartSelect website and once I got I merely swaped them out and it works good as new!

Cracked Icemaker Water Fill Tube

  • Customer: James from Ft. Lauderdale FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 6 people found this instruction helpful
The plastic part that connects the fresh cold water to the ice maker in back of the fridge cracked.
Do to the fact that Whirlpool has the part stick out on the back top part of the fridge. So if you push the fridge just an inch too far back the plastic part will crack.
I ordered (The Part S&H)- came to about, $11.00.

1. Turned off the cold water under the sink.
2. In the back of the freezer section. I unscrewed the two screws that held the old broken part to the fridge.
3. I opened the freezer section and cleared out the top shelf till I could see the back of the fridge.
4. I removed the old plastic part by pushing & wiggling it about forward and it then extended out the back of the freezer side and then I pulled it out the back and it came out.
5. I slid the new replacement part in basically the reverse of step 4.
6. I connected the hose in the back. To the new, replacement plastic part, that fills the automatic ice tray with water.

7. Once finished I glued a small 2”x2” piece of wood next to the new part so the fridge will never get too close to the back wall so to never break that part that sticks out again.
Before just a small bump could break the part and water is everywhere and this leak could happen slowly at first and the next day what a mess.
Some fridges have this part recessed into the back of the fridge so this would never happen as my other fridge has.
Also, this might seem like more work then it was. It was very simple. I was scared I'd screw it up, but just did it step by step. If I had someone do it. It would have cost me a bundle.
It took more time to type this, then to do the work.
I had no instructions to follow, but again, was easer then I thought it would be.
I hope that this was helpful,
Jim Vourakis

Broken cover

  • Customer: Morrie from Gillette WY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 6 people found this instruction helpful
I live in Alaska, my son called me from Wyoming and gave me the Model number, I ordered the part and had it shipped to him. Saved twelve bucks over all. And got it there faster than the local appliance store..
In and out in 5 minutes.

Filler tube broken and old tube frozen over

  • Customer: Alan from Chino CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
this is a snap! 2 screws an a nut to tighten and it works like a charm. the filler tube in my Kenmore refer had broken off in the back. ( really bad location to put this in the beginning) if you push the refer to close to the wall you can break it off easily. remove the water line by loosing the nut and remove the hose from the fill tube ( This assumes you have already turned of the water supply or you are standing in a large puddle)remove the 2 screws that hold the filler tube in place. pull out the old filler tube in and slightly upright motion. replace the new fill tube into the same hole and replace the screws. replace the hose and tighten the nut, turn the water back on and check for leaks your done !!
doesn't that feel great?

We had an accident while moving the refrigerator from one home to another and we broke both handles.

  • Customer: Steven from Cypress TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 6 people found this instruction helpful
All I did was screw the handles on the front door. I had to re-do the freezer handle because I put that one on upside down. I knew I had done so since I was able to refer back to your handly on-line schematic.
All Instructions for the RT18BKXKQ02
31-45 of 133