RT14BKXKQ02 Roper Refrigerator - Instructions

Checked Overload Start Relay With Volt Ohm Meter&Replaced Them Easy And Simple Repair

After receiving the part, I watched the installation video on the PartSelect website. The step by step demonstration was excellent. I felt confident I could do it myself after watching the video just once, and utilizing the written instructions that came with the part. The installation went smoothly, and my refrigerator is functioning correctly again. Best of all, I did not have to go through the hassle and expense of hiring a repair person!

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

Unplugged the refrigerator and then unloaded the freezer. removed the panel at the back of the freezer to expose the fan. Carefully unclipped the wiring harness and then removed the fan motor. Swapped the fan from the old motor to the new one (I did use a hair drier to warm the plastic fan to make it easier to remove) and reassembled the fan and panel. Simple and easy, and now the refrigerator works just like new.

I was a Sears repair man for fourty eight years , so I don"t think I should say how easy this was.

After removing two rear plastic panels, (very easy). The fan is easily accessable. Two more screws to remove the fan brace and remove three wires from the fan and its out. Reverse the process and its finished. The propellor is not part of the fan motor order and you can remove the old propellor and put on new motor (easy). One step that is not accounted for is the removal of a flexable plastic "nut" on the fan shaft. This piece holds and connects the fan to the fan brace. You will understand this when you compare the new fan with the old and see the plastic "nut" sleeve on the old fan. Simply pull it off and put on new motor shaft (it simply slides on and off the shaft).

My husband tackled the job....but before this repair he had to replace ours at home so he had some experience at it....although...on this fridge he had to hook up the water line and all...but basically was not too hard...and the ordering of the part and delivery was excellent...

Looked at your You Tube video and followed the instruction

much like yout video. However I got the mounting bracket upside down and had to do the job twice. When finished it worked perfectly. Great! However in Missouri outside temperature was over 100 and refrig was in shed. My beer got warm. Thank you.

Just followed the video that you guys had on line . It was a very easy repair

I am a landlord and while getting apartment ready for renting, I noticed the broken shelf. I got part # etc. and the shelf came in one day. I was extremely satisfied with the prompt attention that I received.

Researching reasons for the freezer to not defrost, there were determined to be three potential causes: malfunctioning defrost timer, defective bi-metalic switch, or a defective defrost heater element. Research indicated that the most common source of the issue was a malfunctioning defrost timer. So, I purchased the defrost timer (which was the lowest cost option) and installed it, which took about 30 minutes. I would rate the replacement effort as "easy". Most of the time was spent collecting the proper tools and planning the repair. When placed back into service, the freezer did not appear to begin defrosting. I gave it about two days, and based upon visual evidence that the problem was NOT fixed, I removed the panels in the freeze to inspect the bi-metallic switch and the defrost heater. Using a VOM, I determined that the heating element was good; however, the bi-metallic switch appeared to be failed open, even after placing the switch in ice water while testing for continuity. So, I ordered a new bi-metallic switch which included a wiring harness. It took about 4-5 days to diagnose the problem, order, and receive the new switch. During this time, I did not have cause to inspect the freezer. Once received, I collected the needed tools and opened the freezer, only to find that the freezer was fully defrosted! So, in the final analysis, the defrost timer was the culprit! It apparently took 4-5 days for the defrost timer to cycle enough times into defrost to effect the true defrost of the freezer. Lesson learned: give the defrost timer time to do its job!

took a voltage check to ensure had 120vac to the motor and did. Ordered new evap fan motor, installed, refrig works as good as ever now. Thanks for your website.

replaced old one installed new one

Watched your AMAZNG detailed Video first. Ordered part received in two days,WOW! Pulled refrig. from wall unscrewed two screws, loosened third screw on hose, pulled hose out cut below metal incert. Took new part from package placed in back of refrig. placed new metal incert in hose replaced hose in new fitting. Turned water back on, plugged in refrig. No leaks pushed back to wall waited for while...VOILA!! ice cubes no mess to report. THANKS FOR SUCH AN AMAZING WEB SITE and SERVICE. TOM