Models > RT14BKXJW00 > Instructions

RT14BKXJW00 Roper Refrigerator - Instructions

All installation instructions for RT14BKXJW00 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RT14BKXJW00
136-150 of 151
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Light burned out in upper oven

  • Customer: Shirley from Las Vegas NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Screwed in light bulb and glass protector

ice maker froze

  • Customer: Michael from Ewing NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
googled the model of ice maker and refrigerator, ordered replacement ice maker from Part Select. Received next day, installed it in 10 minutes and it worked like a charm.

Ice Maker stopped making ice

  • Customer: Brenda from Champaign IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I removed a few items from the freezer to make room. Husband took out the old ice maker. (We were sure it would require moving the refrigerator out which would have been a huge undertaking given the tight fit) To start he simply replaced the ice maker with the new one. I started watching...and even though it says that it will take up to 24 hours to make ice, it began making ice probably within an hour! After about 6 batches, I threw those out. (just in case there was anything in the line that would contaminate the cubes)It is obvious that the old one had not worked properly for a long time! The ice container is full to almost over-flowing! It has not been this full in a very long time, as I use ice every day! Simple fix! And might I add...LIGHTNING FAST DELIVERY!! It was here in two days! We are thrilled!!!!!

ICE MAKER FAILED

  • Customer: ANTHONY E. from REHOBOTH BEACH DE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I watched your repair video, read the instruction enclosed with the icemaker and made the repair in about 15-20 minutes. There is an issue that others need to be aware of once the water pump is repaced and the tubing is connected and the icemaker is installed and turned back on; it take 20-30 minutes to pump the air out of the line and the for the water to actually fill the the fill tray (you made the install correctly, the delay in filling is not covered by either the video or the book just be patience don't disconnect and reconnect anything it will eventually fill and make ice and less than 48 hours). This vendor offers 4 star customer service at a fair and resonable price (I priced the parts separately prior to purchase and the kit is the way to go). I received the product within 3 days, shipped groung delivery. I would use your products and online service advice for installation on other appliances in the future if needed. You have earned my trust, and repeat business in the future; and I will gladly recommend you to others. Your customer focus and service is second to none. I am a fully satisfied customer!!Sincerely, A. Walker

ice maker was not performing correctly after cleaning freezer and refrigerator.

  • Customer: Dennis from Aliquippa PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unplugged refrigerator. Unplugged ice maker and took out three screws holding ice maker. Put new ice maker and attached three screws. Plugged ice maker in. Plugged refrigerator in and ice maker began working. Threw out first ice cubes made. Unit now working fine.

freezer froze bottom would not cool.

  • Customer: Mike from Greenfield MO
  • Difficulty: Very Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I checked the net. Said the temp control was the problem. Ordered and installed the temp control. Bottom still would not cool. Total waste of time and money. After checking realized fan in freezer was not working. Took it apart and exposed the fan. Pushed it and it started working. Wd 40ed it. Put it back together. Fan is working and the bottom is cooling. Check the fan first before you buy anything.

Broken rear support wheel

  • Customer: Adam from Freeland MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
remove fiber grill cover, remove large bolt holding under frame ( with a 2X4 block, place under refrigerator on outside edge so frame can drop down.) remove pin from broken wheel, replace reversing proceedure. Note: when blocking refrigerator, care must be taken not to let block extend under entire frame. it only needs to be placed approx 3/4" under edge of refrigerator.

evap. fan very noisy

  • Customer: Gary from Yuma AZ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The repair was very easy, unplug ref. open freezer door, and remove base plate, then remove screws on back plate. I had to tilt top of back plate to remove from freezer. This gives you access to the evap. fan Pull of the three wires, and remove screws from fan bracket, which bolts to the back of ref. Remove fan motor from bracket (2) screws, remove motor, and put replacement motor on bracket, pull fan blade off old unit and push on new motor shaft. Reverse the installation, and you are done. Pretty easy.

water tube froze and got bent so it would not fill ice maker properly

  • Customer: Jill from Ivanhoe MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed screws from the back of the part in the fridge. Pulled old part out. Measured the old part. Cut new part to fit. Replaced new part and tightened the screws. Worked perfectly.

Refrigerator not cooling properly

  • Customer: Thomas from prescott AZ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
1. Turn thermostat down to ensure cooling cycle turns on. Open freezer compartment and listen for air flow/fan. If no air flow or fan, but compressor seems to be working, then proceed to next steps. 2. Turn thermostat up to shut off refrigerator cooling cycle. 3. Open freezer and remove wire shelf (if installed). 4. Using nutdriver or socket set, remove screws securing metal panel on the back wall of the freezer interior. 5. Pull metal panel out to expose evaporator fan and evaporator coil. 6. Ensuring area around fan is clear, turn thermostat down to again start cooling cycle and check if fan operates - if not, then fan needs to be replaced. 7. Turn off refrigerator and unplug from electrical outlet. 8. Order replacement fan (unless you happen to keep one in stock). 9. Remove two screws securing fan and fan bracket assembly to back wall of freezer, note wire connections to fan (red, white and green), disconnect wires and remove fan assembly. 10. Gently pull off fan blade, it is a compression fitting. 11. Remove two screws holding back and front fan brackets together and remove fan motor. 12. Remove rubber gasket from front and back of old motor and insert then on the new replacement fan motor (these rubber gaskets align to openings in the fan brackets, thereby holding the motor in place when installed back into the brackets). 13. Reinstall fan brackets onto new motor matching how the old motor was assembled. 14. Press the fan blade onto the new motor shaft. 15. Reinstall fan motor assembly onto back wall of freezer. 16. Reconnect wires to new motor as they were previously connected to old motor. 17. Reinstall back wall metal panel that covers the fan motor assembly and evaporator coil. 18. Reinstall wire shelf (if applicable). 19. Plug refrigerator in and adjust thermostat to normal setting to initiate cooling cycle. 20. Open freezer and listen for fan and airflow, if you hear it operating correctly, then close freezer and refrigerator and confirm temperatures after refrigerator has cycled through one full cooling cycle - adjust thermostat as necessary. 21. Tell your spouse or significant other that for less than fifty dollars you just saved the price of replacing the refrigerator.

Bulb replacement

  • Customer: Judith from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover...released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

NO LIGHT

  • Customer: Mary from Jefferson Township PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
TOOK SOCKET OUT AND REPLACE IT WITH NEW ONE. VERY EASY. W SAVED ALOT OF MONEY DOING IT OURSELF.

Lower part of refrigerator was not cooling

  • Customer: Peter from Oswego IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
About 7 screws total. ! screw holding side shelf removed. 2 screws holding bottom rear panel removed. 2 screws holding rear panel top removed. 2 small screws holding the fan motor bracket. Remove 3 wire connectors from fan motor and then remove plastic fan(pull off) Then just reverse the procedure. As always please make sure unit is unplugged. If there is ice buildup in freezer use a blow dryer to melt and then dry unit. Very easy fix!

replace hinge bracket on fridge door

  • Customer: Albert from Dunmore PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
taped the door shut ,measured a block of wood and stuck it under the door for support.....unbolted bottom hinge,slipped on hinge bracket and reassembled.no muss no fuss.

No cold air reaching refridgerator

  • Customer: David from Gastonia NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the repair video. My son followed my instructions. He removed the ice-maker. The back panel was frozen, so we chipped and waited for the ice to thaw. There are three wires to remove from the old fan. My son used his cell phone to take a picture of the correct wiring. He used needle nose pliers to get the motor off the bracket. I used hot water to thaw the ice, so we could get the back panel to fit properly. If we weren't waiting for the ice to melt, we could have finished in about a half-hour. I'm 86 years old, and have carpel tunnel. My son is 63. Together, we make a good team.
All Instructions for the RT14BKXJW00
136-150 of 151