RST399UL Caloric Range - Instructions

First, I unplugged power to the stove. Next, I removed the grills, ceramic burner discs, gas knobs, and glass plate (under the knobs). Next, I removed the 2 screws exposed by the control knobs. Next, I removed the 2 screws holding each burner assembly to the cook top. I then unplugged the wires attached to each burner assembly and set the assemblies aside. Now I was able to remove the top. Once removed, it was very easy to locate and remove the bracket holding the old sparking module. Then it was just a matter of removing the wires from the old module and attaching them to the new module... attaching the new bracket to the stove and then re-assemble the cook top. Honestly, this was a very simple repair... and probably took me longer to describe the steps than actually execute.

i read other stories and found after checking rotating heat switch with ohm meter found the igniter was the problem, pulled up on door and it came off, found bottom of oven pulled up and out, removed wing nut from deflector and two bolts and one wiring connector, just reversed removal to install new igniter and all complete, took about 20 minutes,

I took out the oven racks. There are 2 cross head screws and 1 screw with a hex head holding the igniter. Pulling out the igniter carefully and the wire nuts also came out. Replaced the wires using the existing wirenuts and slid the igniter into place. Replaced the 3 screws and DONE. Wish the igniters were a little cheaper as this is the third one to go weak. The new one draws about 3.2 amps while the old one only drew 2.85Amps, not enough to open the gas valve. Oven works Fine now. Thanks parts select for the rapid delivery.

I called the local appliance parts store and they said it would cost $60-80 and take a week to order. I paid $16 and received my rack in 2 days!

I just ordered a new wire oven rack from you. When it came all I had to do was to remove it from the carton it came in and place it in the oven. It fit perfectly. Thanks

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Unplug and pull range away from wall.
Remove metal panel from back of range by using nutdriver to remove 4 screws.
Use phillips scewdriver to remove 2 screws holding old spark module.
Unplug 4 wires from spark module and note placement of wires for reinstall.
Install new module by reversing procedure.
Slide range back against wall and plug in.

Entire process took less than 30 minutes.

NOTE: Spark Module received from partselect.com did not match old part exactly. The screw holes on the new part did not line up with screw holes from old part. I reinstalled new part with just 1 screw. Was told by partselect customer service that the part I received had been substituted and would work fine. It does work but it did not fit correctly.

Removed oven door. Removed three screws on ignitor holding bracket. Pulled out the range from the wall and reached underneath to access the wire nuts on the wires. Removed old ignitor and replaced with new one. Reconnected wires and then and replaced bracket and that's it. Works great now.

Removed old assembly, attached wires to new and inserted into space for same. Of course you must turn off the range circuit breaker. The part that took the most time was removing the old assembly. Once that was done, the rest took only a few minutes.

Used a pair of pliers and pulled firmly on ignit. elect. till the retaining clip pulled off the bottom of the elect.The wire pulled off the bottom of it and I had to use a long- thin- nose set of needlenose pliers to pull the wire out of where the elect. came out.Plugged wire in place and snapped electrode back in place without using the retainer clip.Works great.Thanks Wade

Philips is all that's needed. Remove the burners (2 screws each) lift off top of stove, replace the ignition module. put all back together and your done. Local parts store wanted $80+ for the module. PartSelect only $50 total cost and it hit my mailbox in TWO days! Thank you PartSelect.

Removed two screws per burner. Unhook wires. Putting back broke slide on connector and had to replace. That took longer than the whole job. I ordered the part before 3:00 pm and it was at my house tjhe next morning which was hard to believe. The instructions that come with part made no sense what so ever. Thanks for the quick service and I will be back.
Dave

Un plug elect. Cord. Remove door by pulling upward removed back stove panel, un did 2 wire nuts leading to igniter. Un screw igniter inside oven at top next to burner pad. Interchanged old ignitor with new plug stove back in. Thats it.

My husband took the oven door off then the bottom piece below the shelf took the old ignigter out put the new on in and now I have an oven again.

Removed the top, 4 screws and pulled the contact wires off. Replaced the module and connected the contacts. Put back the screws and the top. When the stove was new it did not operate properly and we had a technician out, but naturally it worked for him. For the past 14 years intermittent operation has been agravating me. With the new module the burners have never worked so well.