Models > RS622GP3BG > Instructions

RS622GP3BG Hotpoint Range - Instructions

All installation instructions for RS622GP3BG parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RS622GP3BG
16-30 of 363
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The Bake Element Split

  • Customer: Steve from Surprise AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 6 of 6 people found this instruction helpful
This was so easy I should be a repairman! Turned off power at the breaker, used socket to unscrew two hex head screws, pulled out element slowly from the back of oven wall - enough to expose the wires about 3". Used pliers to remove clips from terminals, put new element in, pushed on new terminal clips, fed wires and terminals back through the two holes, replaced the hex head screws, turned breaker on and wallah! My wife was happy! That's a good thing.

Broken oven element.

  • Customer: NICHOLAS from BALTIMORE MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 6 of 7 people found this instruction helpful
DO NOT ATTEMPT THIS REPAIR UNTIL THE RANGE IS UNPLUGGED AND THE CIRCUIT BREAKER IS OFF!!!!!!

Very easy repair, but, either there is a minor amount of current flowing through the element at all times, or the off switch wasn't working when I started. didn't turn the breaker off, after I removed the nuts, as I was pulling the element to reveal the terminals, the terminals arc'd on the oven wall. BIG SPARKS!

After I turned the breaker off and started again. No problems.

one burner would not work

  • Customer: Joe from Gig Harbor WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
I turned off the breaker to the range. I removed 5 screws holding the control knob carriage. I loosened the 2 screws that hold the control knob to the carriage. I removed each wire 1 at a time from the old control knob and hooked them up to the new one. I replaced all the screws and turned on the breaker.

Bottom element burnt out

  • Customer: Curtis from Oxon Hill MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
remove two screws slide out. slide new one in. put two screws back. done.

The burners no longer worked on my stove top

  • Customer: sharon from Hanover MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
All it took to repair was to plug in the new heating elements. The REAL story is the difference in price. I went to a parts center first and the two elements were going to cost me $115! I got them at PartSelect for half the price. And they came in the same sealed GE parts bag that Sears had. Can't beat a good thing!

Replace oven door handle

  • Customer: Daniel from Centreville VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 8 of 16 people found this instruction helpful
I first removed oven glass panel from frame by removing three screws which secured it to the frame. I then removed the spacer and handle mounts with a 1/4 inch nut driver. This is the only tool that worked for the application. Using an oen wrench or a rachet without a long extension would have taken much more time. Then reattached new handle using existing screws and resecured oven dorr glass to the frame.

One thing to look at is the old handle bracket vs. new bracket. The old bracket had metal threaded inserts to secure the mounting screws. The new handle is all plastic. This said, the existing screws might not work for the application and may split the plastic mounting bracket if it is over tightened. In my case they worked fine but, it is just something to think about.

Surface Burners were very slow.

  • Customer: Fisher from Fort Collins CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
Removed old surface burners and replaced them by plugging in the new surface burners. Now they work GREAT! Parts ordered and received with-in 3 business days. Fed EX delivered parts in good order very quickly. We recommend PartSelect.com

Burned out Broiler Element Needed Replacing

  • Customer: Donna from Milton MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 4 of 5 people found this instruction helpful
I used a socket set to remove broiler element. It was stiff after so many years, but no problem. All was going well until I pulled too hard on the old element(I'd recommend jiggling if stuck, not yanking) & 1 of the 2 connectors pulled loose & fell behind the back. After my initial panic, I summoned my courage, unscrewed the coverings in the upper back of the stove, found the lost connection, pushed the new element ends through the holes from inside the oven (easiest way to hook it up at this point), plugged it in from the back, pushed it back thru into place inside the oven, reattached everything (front & back), & it worked PERFECTLY! Had I not made a mess of it, it would have taken approx. 5-10 minutes. As it was, it took approx. 15 minutes. EASY!

broken knobs

  • Customer: David from Williston VT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 8 people found this instruction helpful
pushed on the new knobs.
thanks fore having the parts.

broiler element melted

  • Customer: Grady from Myrtle Beach SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 4 of 5 people found this instruction helpful
pulled range out, unplugged unit, took out 7 screws, unplugged the elements, reinstalled elements, replugged, and completed with the 7 screws back in place. The 30 minute time was replacing both the broiler and bake elements. The parts were also delivered in a very timely manner. Could not have been more pleased and was very cost effective.

Bake element did not get hot.

  • Customer: Jeanette from Vergennes VT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 3 of 3 people found this instruction helpful
I was able to remove the heating element but in the process one of the wires fell behind the back wall of the oven so I needed a little help getting it out. It was my first time working with electricity. If this didn't happen the repair would have been quit easy. The instructions were great.

clock and timer knobs crACKED AND BROKEN

  • Customer: Karen from Grosse Pointe Park MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 6 people found this instruction helpful
scissors and opened bag. determined that all three knobs were identical. aligned slots on each knob with flanges on each shaft.
snapped each knob into place.
Did a happy dance of empowerment around the kitchen. ( knobs had been broken for at least 5 years).
used timer to avoid burning christmas cookies.
Have a Merry one!!!

oven door jammed,could not open it

  • Customer: Richard from Winchester MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
Removed old hinges and installed new hinges.
Hardest part was determining that worn hinges were the cause of problem, then ordering replacements. GE website hinge on exploded view did not look like hinges I removed.Thanks to Google I got on to PartSelect.com website where excellent pictures of hinges and one-inch grid confirmed they sold exactly what I wanted for my 13-year old range, the model number of which was not even on the GE website.

Broiler element would not work.

  • Customer: ANNE from FT. LAUDERDALE FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 3 of 4 people found this instruction helpful
Removed the old element: removed clips holding the element, unscrewed the 2 screws that hold element in place. On the back of the range, removed casing to get to the connection wires, disconnected the element then removed the element. Reversed procedure to replace. Thanks for the speedy ordering and delivery.

broil unit caught fire and burned all the way around it

  • Customer: octavio from lake worth FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 4 of 7 people found this instruction helpful
My great and talented hubby did it. He can fix anything. It was easy for him.

I love this website to purchase parts. Both times I have ordered something from you, it has been at a reasonable price and I received it really quickly.
Thanks!
All Instructions for the RS622GP3BG
16-30 of 363