RS267LASH Refrigerator - Instructions

took cover off, installed bulb.
lost the owners manual,
part select's schematics were very helpful
thanks

change light bulbs

Removed 2 screws, popped out the old part. Looked at the part number on the piece. Ordered and when it arrived 3 days later, I put the new part in its place. Works great.

Took shelving out of freezer removed panel. Took second panel
out and removed motor. Whole repair took 45 minutes. Works perfect

I performed the repair to my own refrigerator, after watching multiple YouTube videos. I installed a secondary heater for the defrost coils and replaced the defrost sensor. The defrost sensor was actually bad. Today, 1/27/2024 I rechecked the fix from last week. All seems to be good so far.

If I get any build up of any ice on the bottom tray of the recessed panel where the drain port is located. I suspect I will also need a new Defrost Heater as well. For now the refrigerator is operating as expected. There is a small amount of ice build up as of today.

Also, I had recently replaced the drain tubes, added a longer heater element part to fit the drain hole, and cleaned the fins in the back of the refrigerator. Thank you.

I had a son put in the new light bulbs. Rather simple

Took off the plastic panel in the interior. As usual, the evaporator was completely iced up. Took most of the time to de-ice it with a heat gun. Tested the components and the temperature sensor was bad which is on the top end of the evaporator fins. The ohms test wasn't any different whether hot or cold. I keep a spare sensor on hand because this is the third time one of the sensors have failed. The proper readings are available by doing some internet searching. Its been two weeks since I worked on it and everything is working fine.

A couple of blogs said the freezer defrost sensor should be replaced, so I ordered one. Did not fix it. I did, however find a service manual online and one of the blog sites and it showed me how to remove the inside duct work. I discovered the fan the recirculates the air across the evaporator coil was not working. Ordered a new fan motor and installed it, fridge works perfectly now.

Philips screwdriver
Removed screw (1)
Removed light bulb
Put in new light bulb
Closed door to bulb compartment
Returned screw.

Pro tip! Check how many bulbs you need before ordering. Mine only needed two. I got two. I suspect I’ll buy a new microwave before new bulb burns out again. Ordering/delivery was fast. No need to have spare on hand.

Replaced the Broken Cover Motor and the Fan Blade. Fan motor was test with 12VDC power supply, or by replugging fan connector and holding down the door closing switch.

After a few days, the fan made loud noise. Due to defrog heater was open when it was test with ohmmeter. Ice deposited around the fan.

I had to buy a whole ASSY EVAP-REF part # DA96-00395C, and seperated the evaperator, and replaced the heater and sensor.
Spray bottle was used spray hot water to de-iced the evaperator. And salt accelerated the ice melting process.

Note: spray water to clean salt before installing new parts

I removed all of the internal shelves from the refrigerator side. I then removed the cooling panels from the bottom area. this exposed the fan assembly and cooler. I found ice all over the unit. I had to unplug the refrigerator and used a hair dryer to melt the ice away. I then found the sensor and replace it. After putting the refrigerator back together, I plugged it in and let it cool overnight. I also put a thermometer to validate that cooling was stable. it has been a week with the new sensor and the refrigerator has not frozen over and has been very stable.

Using the putty knife, pry off the faceplate for the ice/water dispenser. Disconnect the wire harness. Using philips head screwdriver, remove the dispenser assembly. Remove the old dispenser and replace. Reverse for reassembly. Note * I should have bought the water dispenser lever and replaced it as well since I had the assembly out. Secondary note * be mindful during reassembly to not put pressure on the water dispenser or have a glass handy. :)

After unplugging the microwave and removing the screw, I removed the old bulb and put in the new one!! I made sure it was in securely and the difference in the light was awesome! I use this light when I bake bread and let it rise inside the microwave, but DO NOT turn it on. The heat from this light helps the bread to rise properly!!

1:Removed heating element and sensors from new evaporator assembly supplied by partSelect. 2: removed the evap covers, and defrosted the evaporator in place used a hair dryer to speed things up. 3: Pried open the old evap heater from the evaporator assembly while still in place. replaced the new heating element and sensors 4: closed up the covers and powered back up. Saved on a $2500.00 expense on buying a new refrigerator, and saved the environment too!