The ice maker cube tray holds the water that comes from the ice maker during the process of it becoming ice. This part is white in color and made of plastic. All you will need for this repair is a fla...
This evaporator fan motor is in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated. When the evaporator ...
This sensor cover, also known as the ice maker thermostat cover, is a genuine OEM replacement part for Samsung refrigerators. It is made of durable white plastic and has measurements of approximately ...
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Armando
December 17, 2019
Need to turn ice maker on
For model number RS261MDBP
Hello Armando, thank you for your question. There should be an on/off switch on the unit towards the bottom at the front. I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Laurine
August 23, 2022
Bottom of freezer floor has a build up of thick ice, WHY?
For model number RS261MDBP
Hello Laurine, thank you for contacting us. There can be multiple reasons for that. The most frequent reasons are humid air leaking into the freezer, damaged door seals, and poor or clogged ventilation. If you need any help regarding purchasing and replacing any part please feel free to reach out to customer service, available 7 days a week.
Was this helpful?
Thank you for voting!
Beth
March 15, 2023
How can I remove ice chute
The rubber cap came off
For model number RS261MDBP
Hi Beth, thank you for reaching out. We have found some relevant instructions to help you remove the ice chute. They may not be of the exact same model, but they will help you with the process. You can remove the ice chute by following these steps:
1. Use the phillips-head screwdriver to unthread the two mounting screws securing the ice and water dispenser control assembly.
2. Pull the assembly down, disconnect the wire connector, and release the wire from the retainer if still intact.
3. Now pull the old ice chute free of the assembly.
We hope this helps, good luck with this repair!
Was this helpful?
Thank you for voting!
James
December 28, 2023
I took off the doors and reattached them a couple days ago, now there is a constant beeping noise that comes on every minute or so. Could it be something with the doors or a different reason?
For model number RS261MDBP
Hi James, thank you for reaching out. Sounds like the 'door ajar' sensor might be broken or the door not aligned. Make sure you installed the door correctly and hinges are tightly secured. If this is not the issue, you will need to replace the reed switch, part number PS4138745. Good luck with the repair!
The compressor got very hot. I cleaned the condenser, let it get cooled, checked the r,s and c windings and read correctly and i replaced the overload and the relay kit but the compressor did not worked. Could you tell me what could it be? I will appreciate your help.
For model number RS261MDBP
Hi Rudy,
Thank you for your question. If you have checked the condenser and it is working correctly, check the defrost system in the refrigerator. Try defrosting the refrigerator to see if this helps. If the refrigerator is not defrosting as it should, the compressor will get hot. If it is not working correctly, you will need to check the evaporator assembly. This includes the defrost heater and the temperature sensor. We hope this helps! Good luck with the repair!
The replacement was fairly simple. I removed the existing tray and detached the water line. Once the water line water reattached to the new tray I inserted into the ice maker.
*** The problem I'm having now is the water is not filling up the tray*** Not sure what I did wrong? Any help would be greatly appreciated!!!
