RS22BRXDN01 Roper Refrigerator - Instructions

First I watched the video on your website, it was quite helpful. It showed me the location of the part to be replaced. Then I used the nut driver to remove a couple of screws, and slowly pulled the cover off . Once I pulled the cover down I could see the part that needed replacing, it had a couple of phillips head screws holding it in place, I removed those screws and unplugged the defrost timer, taking note of the color of the wires. Then I took the new defrost timer and attached the loose wire to the correct terminal according to the directions(this is where the color of your wires comes in), then I plugged in the new defrost timer and replaced the screws. I then reattached the cover making sure not to pinch any of the wires, and replaced the screws. It was so easy I was sure I did something wrong and it wouldn't work, but I plugged the refrigerator back in and let it sit for about 20 minutes and then when I checked it was running cool. I'm 55 years old and never had the nerve to try anything like this before but since my husband passed away I've had to try things myself or replace a lot of appliances. If I can do it anyone can.

First, I took out the broken unit,yhen I put in the new one..

Unplugged the fridge and removed the cover from the Icemaker control assembly. Then remove the three phillips head screws, remove the Icemaker control. put the new control in place and use the three screws removed in previous step, replace the cover and plug the fridge back in. in a few hours you will have some ice.

Replaced the icemaker control assembly and ice mold. Icemaker is working perfectly now. We replaced the ice mold (tray) because my husband read on the internet that the ice mold loses its nonstick coating and the ice sticks to the mold, and eventually burns out the control assembly.

The reason it took me longer than what should have been a 15 minute repair is due to the fact that I could not figure out how the shaft came apart. I found an instructional video on Parts Select website that showed me that the shaft was held together by a reverse treaded, round nylon nut on the very front of the shaft. Just use a pair of pliers to grasp the nut and rotate it clockwise, after that you just need to lay the parts out in order as they come off the shaft so you can put it back together again.

This was a very easy repair and only took about 20 minutes. Unfortunately, after reordering, and installing the second motor, the intermittent noise is still there. Other than the occasional buzzing noise, that sounds like it is coming from the evaporator fan area, the refrigerator runs fine.

Simply follow the video instructions. Involves the removal of nine screws. to remove the old plastic sleeve cut the tube near the old thermostat and it slides of easily. Apply dish or hand washing soup to the new tube when putting the plastic sleeve onto the new probe. The hardest part is getting the end of the probe coiled to the right shape. Hey,` if I can do it with a broken collar bone, anybody should be able to do it.

This was a very easy fix. I utilized the short repair video for both parts and the entire install time was 40 min max. I installed both parts per the instructions, plugged the unit in and waited 20-30 minutes for the unit to reset itself. The Fridge cut back on and its running well within guidelines. In fact, it's cooler and running better than the last 6 months. Thank you "Part Select" for helping me save real dollars.

replace drawe

Read the instructions, watched the video and followed the very clear instructions and lay out.

Pulled refridgerator forward away from the wall. Remove the cardboard back behind the appliance.I saw that the condenser fan motor was not working. Unplugged the appliance from the electrical outlet. Removed a 3 wire plug from the condenser fan motor. Remove 3 screws (with a nut driver) which held the condenser fan motor in place. Remove the condenser fan motor from the appliance. Looked up the part needed for repair using the appliance model number. Found which part was applicable for the appliance. Placed the order from Price Select on a Monday morning and recieved the part 2 days later on Wednesday via FedEx. The item shipped was a 2 wire condenser fan motor. Read the instructions that came with the part. Using wire cutters, cut the old 3 wire plug. The center wire is a green and yellow striped wire. Use the same colored wire that is also shipped in the box and has connectors on both ends. Cut one of the connectors off and use the wire strippers to remove plastic wire coating. Connect both ends from the appliance and the green and yellow wire that was shipped. Use a wire nut (also shipped in the box) to connect the wires. You will have 2 black wires left on the new condenser fan motor that need to be connected to the appliance. You should have an orange colored wire and another wire that is black with a white stripe. Connect one wire from the new fan motor to the orange wire and use a wire nut to attach both wires together. Use the other black wire from the new fan motor to the black/white striped wire from the appliance. Use the wire nut to attach both those wires. Place the new condenser fan motor back in the appliance using the screws that come with the motor. Attach the green and white wire with the connector on the end to one of the 3 screws that hold the motor in place and secure the screws. Use the electical tape to hold the wires all together and away from the fan motor. Plug the appliance into the outlet. You can see the condenser fan motor working properly. Note that when connecting the 2 black wires from the new condenser fan motor to the orange and the black/white wire from the appliance, for my appliance, it did not matter which wires were connected as the fan motor was a clockwise motor. Place the cardboard appliance backing, back on to the appliance and push the refridgerator back in place. Allow about 5-6 hours to get the freezer to between 0-5 degrees. The refidgerator should be between 34-38 degrees and will take a little longer to get to that projected temp.

When I ordered the new auger drum from this website, I noticed a video that explained how to install the item. When I received the new drum, I went to the website and found the video. All I did was to watch the video and do what the repairman did. I did get a little confused when I noticed that the auger in the video was metal, and mine was plastic. However, upon removing the pieces as shown in the video, it became clear that the new auger drum would fit the same way the broken one had fit. After that, it was a snap to put the pieces back together.

the repair from the video was exact to a tee. Very helpful 100%.

The icemaker is in a side by side refrigerator/freezer with an auger driven ice bin dispenser, so space was limited. I first removed the ice bin but I couldn't see the three nuts holding the icemaker in place. I removed the ice bin support bracket (under the icemaker) using a Phillips head screw driver. Now the bottom nut holding the icemaker in place was easily visible and I was able to determine the size of nut driver I needed to completely remove it. Then I felt for the location of the top two nuts, slipped the nut driver on and loosened them. I was able to lift the icemaker off the top two nuts without completely removing them. Using a flat head screw driver, I pushed down the white tab holding the wiring harness connection to the icemaker and removed the harness, freeing the ice maker for complete removal. I did not need to replace the wiring harness, so I simply reversed the whole process to install the new icemaker. I am a 61 year old female with rheumatoid & degenerative arthritis and found this installation really easy, with the one exception of snapping the wiring harness connection into the new icemaker - I didn't have the thumb strength. I had to wait for a relative to come and snap the wiring harness connector into place for me. I also had to use some snips to cut out the plastic tab (scored) for the water feed to the icemaker but was able to complete the entire installation within 30 minutes.

Ordered alternate water inlet value-reattached new one as described on enclosed instructions. Newer type inlet connection-was not sure but it worked as described.