RS22BRXAW00 Roper Refrigerator - Instructions

Unscrewed bolts pulled out motor,unhooked motor,replaced with new motor,put back in and replaced screws..fairly easy..then we had ice that evening!

Video instructions walked me right thru it had no problems.

turn power off, take the little cover on front of ice maker off so you can pull ice maker box out easier, unplug the easy connector ,after this take square cover off you'll see control motor take 3 screws off pull control motor out change new one in ,put them back together.turn power back on .then now Ice Maker will make some after 2 hours .You will SMILING then say ,Oh Yeah. QT good luck to everyone

The online video shortened the learning curve, and the cut the repair time in half.

I was a Sears repair man for fourty eight years , so I don"t think I should say how easy this was.

Put part on /did not see warter come at first had to go a cycal then ice again thanks alot, danny repair guy whanted 46$ to look at part. Good job.

My ice maker has been broken since august 2011. I called my son in law, which is very handy, he looked at the broken ice maker, said he had no clue how to fix it, since its computerized. Searched the internet, found part select website, watched videos, read customers feed back, based on information provided, ordered icemaker control and motor assembly (less than $60. 00), Called my son in law, in less than 10 minutes, part was installed. The next morning the ice bin was full. I am so greatful for your website, and my wonderful son in law.

Removed 2 screws that holds the lite bracket .removed the 3 screws that holds the arm an water dispenser. The brackets have springs hooked to the one in the middle an right side. Save them . Next take the 2 screws that hold the ice flap, an then remove old arm, put new one on an place door flap screws back in an tighten. Put springs back in an tighten. Kinda hard to hold brackets down but they will go. Saved a lot of money doing it myself for 60 min of repair . Good luck you can do it

My name is Tuan Nguyen. I have no ice and no water dispense into icemaker tray. I replace the the icemaker control and motor assembly. I unscrew a screw underneath the icemaker unit and disconnect the wire clip and pull out the icemaker assembly. I remover 3 screw from the motor assembly unit and replaced it with the new motor assembly. and installed the unit back in the compartment. It took about twenty min. It make me look good, that my wife knows i can fixed the problem without calling the repair men.

empty frezzer take door off unplug wires going to ice maker unscrew/bolt icemaker replace door take motor cover off ice maker remove screws on motor replace ice cup and put every thing back together

unplug freg.took everything out.pulled out shelves and pulled out back panel.their was my part i had to replace.

The comments from PartSelect were 50/50 that it would be the motor on the icemaker. We bought the motor which came 4 days leter and followed the installation instructions in the video. We started getting ice about 2 hours after the installation!

Turn the unit OFF - Removed one hex head screw on the bottom of the ice maker, removed the cable cover and unplugged. Removed front cover & Slide the icemaker out. Removed control cover and removed the three phillips head screws to the controller. Put the new controller back on with the three phillips head screws, pushed the cover back over the controller. Plugged the unit back in, then slide it back in the tracks, put the cable cover back on and installed the hex head screw, popped the front cover back on and turned the unit ON - DONE!

My dad and I worked together. The video helped but it was a little more complicated. If you can't find the water supply, remove the filter and water should stop, that's what we did. We had to remove the freezer door for access to the ice maker. It was tricky taking the icemaker off and getting it back on. Replacing the motor was easy, just as shown in the video. Just like others have said, within an hour of the repair the ice starting coming!

Thanks to this site, it told me what was wrong, what to order and how to repair it.