RS22AWXEN00 Roper Refrigerator - Instructions

very easy two small screws, no problems

No way to fix the broken drawer. Order drawer online around 2:00 PM and replacement arrived about the same time the next day. Drawer fit perfectly. Easy to use online finding part with model number and excellent customer service.

I was cleaning my refrigerator. When the glass shelf was being cleaned it barely bumped the bottom of the sink. There was no water in the sink. The shelf exploded into thousands of small pieces simular to a car windshield. I was devastated! I went online and ordered a replacement that same day. The next morning I was on my front porch watering plants when a delivery truck pulled into my driveway. It was the replacement shelf. I cannot believe the fast service. Thank you.

watched the video. If your water dispenser is working on and off and it eventual quits,it is the water control vale that needs to be replaced.

The video of the repair is a helpful guide, but my refrigerator has the compressor very close to the condenser fan motor. With the compressor comes the copper tubing that is all in the way. I had to carefully bend them now and then to allow me to get my hands in position. The how to is easy, but the working with tools in cramped quarters was difficult. I think my Maytag side by side model makes for this job to be difficult, maybe yours may not be so bad. I took a couple of hours to complete. After the first hour, I covered the bare wires, and plugged the frig back in so it could do some cooling. I placed a small in front on the condenser to blow across it. Had a little break, then finished the job.

I replaced the ice maker with a new one. All part were included. The cost was about $200.00 cheaper than what the repair person wanted.

Ice maker is held on by two clips and one screw. Removed old ice maker and unplugged wiring harness. It appeared normal. Since it was 15 years old and a brand new one was only a little more than $100 I decided to just replace it. Shopped online and got best price here. Delivered promptly. Item description said it did not come with wiring harness, but mine came with three different ones. However my wiring harness had a different molded plastic connector where it is plugged into the back of the freezer so I could not just pop it off and pop in the new one. Instead I had to reuse my old one. No problem, since the harness was not damaged anyway. Also I had to reposition the harness clip on the new ice maker and remove the plastic tab on the bottom and re use the tab from my existing ice maker. The tab on the new ice maker would not line up with the hole in the freezer. All in all it took about 10 minutes total to switch the two units out. Extremely simple job, do not pay someone to do this for you.

I was unable to remove the old part so I threaded the new part in front of it. They both fit within the actuator. Done!

It tool me a while to diagnose the problem but realized the ice dispenser motor coupling had failed. It fooled me for a while because it turned on the motor but could not turn the plastic shaft inside the icemaker. I found the instructions for an almost identical repair on your website. 1)I removed the motor. In my case the wiring harness came right off.2) I turned the coupling by hand and found that although it turned, it was actually loose on the motor shaft. I then knew it was the problem. 3) The threads were apparently cross threated. 4) As a prior user suggested on your site, I used a hacksaw to cut the old coupling off, being careful to not damage the remaining threads. 5) I ordered the new coupling which arrived very quickly 6) I screwed it on to the motor shaft (remember it is a left hand thread). 7) Presto!! My icemaker works. As the other user suggested, I did not have to use washers as spacers. The new coupling was better made than the old one and actually has ~1/8" nut or spacer already welded to the coupling. My thanks to those before me who helped make this a successful repair.

Impossible to pass the water tubing through the door as kitchenaid spliced the water tube behind the dispenser and also within the door with tube connectors and not to mention that it was also bundled with the wiring harness. I freshen the connections behind the door and after the tubing exited the door. No leak so far. The only piece of the purchased tubing I used was the spout and attached 12 inch strip of the tubing.

I called a repairman, who removed the ice maker and reinstalled it, not once -but- three different times and charged me $84.60. (That's all he did.) I remembered, PartSelect, watched video, ordered motor, received in three days, installed in less than fifteen minutes. Within ten minuted water was running in and later ice was dropping into bin, next day bin was full. Wish I had trusted myself and looked up my fridge problem on PartSelect before calling that (repair) man, and saved myself $84.60. By the way, I'm a 67 year old female.

I'm sorry I can't help you with this, as one of my sons diagnosed the problem and did the repair for me. It took him maybe five minutes to swap the parts, and the ice maker has been working fine ever since.

The evaporator gan motor would work sometimes, but not always, so it took a while to be sure this was the problem. First ruled out thermostat and defrost timer. Also observed build up of ice on coils, so I knew compressor was working. Once I isolated problem to evaporator fan ( by observing stuck once, and seeing how it didn't spin freely) replacement was easy. In fact, since we were able to keep the unit running by watching the old fan and ensuring it was working while waiting for the new one to arrive, I was able to swap them out, plug unit back in and start it up before the ice in the bin even had time to melt! This repair saved me hundreds in repairs, and even more if I had to buy a new fridge, because the new units are too tall for my kitchen space.

Replacement was quite easy. Video was helpful as to how to get all pieces back on the shaft correctly. Was easy to find the correct part and was shipped quickly.

Pulled out old drawer. Slid in new drawer. Super easy!