Models > RS22AQXMQ01 > Instructions

RS22AQXMQ01 Roper Refrigerator - Instructions

All installation instructions for RS22AQXMQ01 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RS22AQXMQ01
1,036-1,050 of 1,392
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refrigerator stopped cooling compressor did not cycle

  • Customer: james from indian springs AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
unplug power! Remove the screws from lower panel on back of refrigerator. Lift wire mount out of back panel. Capacitor is mounted directly to the relay and overload switch located on the left side of the compressor. Remove the spring clip holding the capacitor in place and pull the old capacitor out. Plug in new capacitor and replace spring clip. Use vacuum to remove dust from drip pan and wipe fan blades clean. Replace wire into slot on back panel and replace screws. Remove front coil cover below freezer door. vacuum dust off coils and replace cover. Plug refrigerator in and enjoy cold beverages. Relay and overload kit were not required for this repair.

Loud, non-rythmic clicking noise shortly after the compressor comes on, continuing for several seconds.

  • Customer: PHILLIP from SUN CITY CENTER FL
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Replaced the "Run Capacitor. The non-rythmic clicking associated with the compressor coming on continues. The problem was obviously not the Run Capacitor". I don't know what to do next. Any suggestion would be appreciated.

Thanks,

Phillip

refrigerator not working

  • Customer: HERBERT from CHARLOTTE NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
read instructions from your site my wife repair refrigerator before i got home

The nut on the motor that turns the augor in the ice maker had striped the treads.

  • Customer: Ronald from Alamogordo NM
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
I would not have attempted the repairs without your instruction. I use a Drimel tool with a abravise blade to cut the part off the shaft. After I realized the Drimel tool would work. It took me parhaps 10 minutes to get it off the shaft. I had already ordered the new part and the job was complete. Thanks for the help. Ron Burch

The original part was stripped and would not spin the ice out

  • Customer: Top of the Hill from Duvall WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I was unable to remove the old part so I threaded the new part in front of it. They both fit within the actuator. Done!

Icemaker shaft did not turn to dispense ice

  • Customer: Carlos from Friendswood TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
It tool me a while to diagnose the problem but realized the ice dispenser motor coupling had failed. It fooled me for a while because it turned on the motor but could not turn the plastic shaft inside the icemaker. I found the instructions for an almost identical repair on your website. 1)I removed the motor. In my case the wiring harness came right off.2) I turned the coupling by hand and found that although it turned, it was actually loose on the motor shaft. I then knew it was the problem. 3) The threads were apparently cross threated. 4) As a prior user suggested on your site, I used a hacksaw to cut the old coupling off, being careful to not damage the remaining threads. 5) I ordered the new coupling which arrived very quickly 6) I screwed it on to the motor shaft (remember it is a left hand thread). 7) Presto!! My icemaker works. As the other user suggested, I did not have to use washers as spacers. The new coupling was better made than the old one and actually has ~1/8" nut or spacer already welded to the coupling. My thanks to those before me who helped make this a successful repair.

replaced ice model

  • Customer: Joanne from Big Flats NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watch the video was very helpful. I'm just a women and I did it all by myself. Thanks for the help of the video.

ice mold coating came off

  • Customer: Charles from Waco TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Told Wife To Watch The Instructional Movie, Got Me A Beer And Watched Football. She Finished In about Thirty Minutes.Good Job

Coating of Mold deterioated and mold leaked into ice tray

  • Customer: Dwight from Bossier City LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Followed the video on Parts Select and it was a breeze.

Ice door assembly broken, freezing up ice maker

  • Customer: Sandra from Burlington NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the outside ice door panel with two flat head screw drivers inserted in the slots at the bottom of the panel. You simply pry out until the bottom releases and then you push it up gently to release the top. I then removed the hex head screws that held the outside wire panel and the switches, at this time you need to remove the old plunger that is connected to the top of the ice door assembly. I then disconnected the old heat strip and removed the hex screw that held the ice chute at the bottom. Then I removed the pin and spring that held the ice door assembly at the top. Replaced the parts with new ones provided in the kit. The ice door is no longer freezing up, nor is the ice bucket in the freezer. The freezer is now back to the right temperature, without having to be set on high

Ice dispenser was broken

  • Customer: Helen from Escondido CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
My handyman did the repair. It was pretty easy for him. It would have been a real puzzle if we had not watched the video instructions. The new parts were slightly different than the old parts, but they fit perfectly. I thawed the frost buildup around the ice door and the opening of the ice bin with a hair drier, to get the ice to come out properly. Thank you so much for the video!

When you pressed on ice maker to get ice it was hard to get it to dispense

  • Customer: Dennis from Gig Harbor WA
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed along with the Video from the web site. I used the masking tape to keep the electric parts out of the way. one of the attaching points for the new ice door broke off so i used J B Weld to reattach it. then the repair was finished with out a hitch. The time was extended by the need to wait for the epoxy to cure

Ice door would not shut which lead to ice melting and freezing up Ice chute.

  • Customer: Doug from Arvada CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Got Online to Parts Select put in the model number, selected from parts schematic, Ordered parts. Reviewed YouTube instructions supplied by Parts Select, Canadian service tech in video very knowledgeable about repair, followed his instruction and fixed the Ice maker. Very easy with Parts Select help.

Ice despenser stoped working, auger motor worked if door flap was opened fully manuallyw

  • Customer: Jolene from Merritt Island FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I Googled the problem and after reading several posting & suggestions decided that the Ice dispenser kit would probably solve the problem. I ordered both parts on the chance that it might be only the micro switch and it was only a $10 part, the ice dispenser kit was $50. The access was really easy and the switch was installed in about 20 minutes but did not solve the problem so I proceeded with the kit. The parts came out fairly easy but our actual set up was slightly different from the video and print instructions. Our model did not have the heating ribbon on the door flap and the little barrel part was permanently attached to the refrigerator so I thought I could be in trouble. Did not realize that we had cracker the lever bracket clip during removal so my husband "brainstormed" a fix. That's what we needed the large head screw and drill for. We drilled the screw into the refrigerator so it holding the spring loaded piece tightly in position. Works fine. I was told my a repairman over the phone that the dispenser was probably not fixable on our model. I saved an expensive service call AND GOT THE DISPENSER WORKING!

Ice dispenser door dislodged/broken-causing ice/frost in freezer

  • Customer: LAWRENCE from Gig Harbor WA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watch the Video! My reefer's ice door/spring 'pin' removal and installation is different than what is shown in the video. That is, my spring 'pin' looks more like a long nail (with a head on the right end). After inserting the left end of the pin into the hole, the head end drops down into a notch, which makes removal and installation easier than what is shown in the video. It is much easier to reinstall everything if the 'ice-chute' is installed first. Then, maneuver the ice door assembly into place and install the pin. I used Blue masking tape to hold the control panel up and out of the way. This is the second ice-door repair since I've had this refrigerator. It seems to occur with 'heavy' use of "crushed" ice. Some crushed ice backs up behind the ice door/flap, jams/holds the flap open, letting warm air into the freezer, causing the crushed ice to freeze into a big 'clump' of ice (too big to come out of the chute, and causes frost in the freezer. If you get a clog like this, I suggest removing the ice "bin" and gently clearing the clog from the top side of the ice chute with tongs or needle nose pliers. If you try to remove the clog from the bottom of the ice chute, the door becomes dislodged or breaks...
All Instructions for the RS22AQXMQ01
1,036-1,050 of 1,392