Models > RS22AQXMQ01 > Instructions

RS22AQXMQ01 Roper Refrigerator - Instructions

All installation instructions for RS22AQXMQ01 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RS22AQXMQ01
1,021-1,035 of 1,392
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refrigerator and freezer was not cooling. Lights inside refriogerator working . Compressor and fan was not on.

  • Customer: Cary from Missouri City TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First, unplug the refrigerator. With nut-driver and/or screw driver remove the lower back cardboard panel to access Start device. Use needle nose pliers to remove bracket holding Start Device along with capacitor. Disconnect the wiring connector from Start Device. Carefully, pry Start Device from compressor. Remove capacitor from Start Device. Replace the capacitor to the Start Device. Connect the Start Device with the capacitor to the compressor being mindful of the three male pins. Plug the electrical connector back into the Start Device. Finally, reconnect the bracket. . Reinstall the lower back cardboard panel. Plug in the appliance. Very simple and easy to install. Note: If the compressor and fan do not come on, reset the defrost switch which is located inside the refrigerator side underneath the right side of the refrigerator temperature selector with the flat head screw driver.

Broken fan blade

  • Customer: Wayne from Decatur IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Remove back cover. Slide blade off, slide new blade on.

ice maker door failed to close causing frost to form preventing proper operation of icemaker.

  • Customer: Melinda from Owasso OK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Found video on YouTube. Ordered part from partselect. Part arrived and viewed video to refresh memory. Our refrig was a little newer than the video but the process ww was the same and quite simple after viewing the video.

Ice buildup on ice maker

  • Customer: Russell from Orlando FL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Per instructions in video. Super easy. Spent 45 min. cleaning ice/water dispenser and ice maker tray. Spent 15 min. replacing ice door.

Ice door would not close

  • Customer: Richard from Springfield MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Ice door would not close thus letting warm air into the freezer compartment. Thinking the spring was broken, I ordered the Ice Door Kit. When it arrived, I dismantled the dispenser and installed the new parts. After installing all the new parts, I found that my problem was the "Y" end of the bracket that holds the spring pin. It was cracked and would not hold the pin. The bracket seemed to be molded into the panel on the outside of the dispenser. To replace the bracket, I would have had to replace the entire outside panel. I decided to repair the bracket and glue the broken piece. I used cyanoacrylate(CA)super glue that I use in model making. Even though that seemed adequate, I decided to drill a small hole through the bracket, perpendicular to the crack, and install a small screw to strengthen the crack. I also applied a little CA to the screw for good measure. It held fast and so far so good!

The plastic Ice Handle had broken after years of use

  • Customer: Tom from Hollis NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Your web site was great. There was a short step by step video on how to remove and replace the ice door kit and tools required. The only additional tool I used was Blue Tape so I could stabilize the inner control panel out of way onto Door.If I need more appliance parts I now know where I am ordering from!!

Plastic hinge attached to chute door broke

  • Customer: James from Houston TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video showing how to disassemble unit and it showed that there was a heat element inside the chute door under the foam seal that needed to be removed and placed in side the new chute door. I spent about 10-15 minutes trying to salvage the element but the adhesive used would not release and the part was rendered unusable. I called the help line and was told that their instructions on that kit said the heating element was no longer required. I finished putting the kit in and the unit works fine

freezer getting air into it

  • Customer: James D. from Crockett TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Followed instructions in video and instructions by other home owners. Installation went very well. Parts Select shipped the repair kit. A good company to do business with. Saved a lot of money by doing the repair myself.

ICE CHUTE FREEZING UP

  • Customer: Douglas from Raymore MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removal of escutcheon was easy. Replacing icedoor was fairly easy, working with wires in the way was a little distracting but simple. Be careful with microswitches and locating pins. Two of mine broke, had to replace bracket. Simple job again. Everything working fine now. No ice jam in chute. Using needlenose pliers to remove/insert pin is the best and easiest option.

Foam had torn off the flap door and the black thingy had broken.

  • Customer: Linda from Lafayette IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pulled off front. Detached wires without getting electrocuted. Marked them first so I'd know where they go. Pushed up the thing with wires so I could see the flap door. It had a heat thing in the flap which my replacement part didn't have, so I had to pull it out of the broken flap and insert in the new flap. Snapped flap door in place. Attached black thing loop to white thing. DIdn't use the spring or the white thing. Reattached wires and put on front piece. Everything now works. No more frost in the freezer!!!

See below

  • Customer: Patricia from Hobe Sound FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The defrost timer that I ordered form you did the trick. My fridge was
running all the time and the fridge temp was 55 but the freezer was 10
below. The instructions did not say how to test the old one to compare with
the new on. However in the Readers Digest Home Repair book it did and the
test proved that it was defective. Your article said that with the system I
had, 65% on the time it was the timer. I ordered it and thank you it works
just fine. I do have another problem, maybe you can help. The fridge runs
for 6 minuets and stays off for 10 minuets. The temp in the freezer is 0
and the fridge is 35-40 on the warmest settings, but all is well.
Thank you

Ice door assembly broken, freezing up ice maker

  • Customer: Sandra from Burlington NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the outside ice door panel with two flat head screw drivers inserted in the slots at the bottom of the panel. You simply pry out until the bottom releases and then you push it up gently to release the top. I then removed the hex head screws that held the outside wire panel and the switches, at this time you need to remove the old plunger that is connected to the top of the ice door assembly. I then disconnected the old heat strip and removed the hex screw that held the ice chute at the bottom. Then I removed the pin and spring that held the ice door assembly at the top. Replaced the parts with new ones provided in the kit. The ice door is no longer freezing up, nor is the ice bucket in the freezer. The freezer is now back to the right temperature, without having to be set on high

Ice dispenser was broken

  • Customer: Helen from Escondido CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
My handyman did the repair. It was pretty easy for him. It would have been a real puzzle if we had not watched the video instructions. The new parts were slightly different than the old parts, but they fit perfectly. I thawed the frost buildup around the ice door and the opening of the ice bin with a hair drier, to get the ice to come out properly. Thank you so much for the video!

When you pressed on ice maker to get ice it was hard to get it to dispense

  • Customer: Dennis from Gig Harbor WA
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed along with the Video from the web site. I used the masking tape to keep the electric parts out of the way. one of the attaching points for the new ice door broke off so i used J B Weld to reattach it. then the repair was finished with out a hitch. The time was extended by the need to wait for the epoxy to cure

Ice door would not shut which lead to ice melting and freezing up Ice chute.

  • Customer: Doug from Arvada CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Got Online to Parts Select put in the model number, selected from parts schematic, Ordered parts. Reviewed YouTube instructions supplied by Parts Select, Canadian service tech in video very knowledgeable about repair, followed his instruction and fixed the Ice maker. Very easy with Parts Select help.
All Instructions for the RS22AQXMQ01
1,021-1,035 of 1,392