Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RS22AQXMQ01 > Instructions

RS22AQXMQ01 Roper Refrigerator - Instructions

All installation instructions for RS22AQXMQ01 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RS22AQXMQ01
1,006-1,020 of 1,407
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Wobble in fan made a ticking noise.

  • Customer: Andrew from Fairport, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Pulled out the Fridge. Removed the plug. Removed the back panel screws with nut driver. Vacuumed the coils & fan area. Disconnected the fan cable. Used a socket and thumb ratchet to remove the 3 mounting screws from its sheet metal bracket. Slid the old fan assembly out. Assembled the new Fan blade onto the new motor shaft and attached the adapter cable to the fan connector. Slid the assembly into place and reattached with 3 screws using socket and thumb ratchet. Connected adapter cable to fridge harness and plugged in the power cord to test the fan. With it working Quietly and knowing the the problem was solved, the back panel was reattached.

ice maker not making ice

  • Customer: Travis from La Crescent, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
My ice maker stopped producing ice after our refridgerator was accidently turned off for 4 days. Note: the on off switch in the front does turn the unit off even though the light stays on, why we need easy access to turn off the fridge is beyond me. Regardless, I spent way more time researching the problem then doing the repair. There is 2 things that could be wrong: 1 was the infra red light located on either side of the freezer, called the transmitter/reciever. 2 was the side of the ice maker control panel. Either one or if I had to replace both it would of been less then the cost of a repair man to come to my home. Prices here a good. I started with learning the diagnostic of the ice make which is learned by watching the red light flash. That informed me that it was working ok. Reference: if you hold back the hinged plate and pretend the door is shut the light should flash, flash, pause. This means its working. I went with the other route of the control module on the ice maker. This part came fast like 2 days. I watched the video on the parts web page and it was simple to do. You do have to wait until the temp goes down below 15 degrees in order for the ice maker to kick in. I won't buy another kenmore for I have had plenty of trouble with this one and its bearly 6 years old. I'm Definetly a fan of this website. Good luck DIY ers!

No ice when you push the lever

  • Customer: Michael from fayetteville, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After watching the vidio I think my wife could have done this repair. It took me about a half hour and the job was done. It cost me $20, No telling what a repair man would have charged. Thank You.

Broken Auger

  • Customer: John from Columbus, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Was easy, removed several screws and a clip on the auger shaft. removed broken part and replace with new then reassembled

ice maker quit making ice

  • Customer: Joseph from Lakewood, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I looked on line to see repair instruction videos on my refrigerator ice maker. When I saw how easy I went to PartSelect and order the part (control and motor assembly). I received the part in two days with the cheapest shipping option. My 33 yr old son was visiting when the delivery was made. After we opened the box, he went to the basement for tools and the rest is history. 10 minutes work and ice a couple of hours later! No problems since.

plastic auger broke apart

  • Customer: Allen from Danville, KY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
The only problem I had was the nut at the end turned the opposite direction. Once I realized that I took it apart in sequence and it went right back together. It helped me in that I slid all the parts off the auger shaft onto another small rod I had and then slid them right back on. Was no problem

no ice

  • Customer: Gwenn from Middletown, DE
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pulled out the old unit removed 3 screws waited about 3-4 hours had ice. Took over night until we were actually sureby then the ice bin was full. Easy repair!

Condenser Fan Motor had stopped working

  • Customer: Marshall from Garland, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I found the part I needed on this website, watched the tutorial and saw how simple it was to do myself. I ordered the part and it arrived within a few short days. It took me no more than 15 minutes to change out the part. I saved myself several hundred dollars. It is rather shocking how much the "professionals" charge considering the cost of parts, labor and nominal service fees.

refrigerator not cold. and keeps striping the circuit breaker and shutting off other appliances using the same circuit.

  • Customer: kevin from Antelope, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
what I discovered is the condenser fan is still operating but not strong another word insufficient cooling for the condenser. therefore, it's getting too hot and shutting off and stripped the circuit breaker. After installing the new condenser fan, it gets back in business. it's quite simple. Just unplug the unit off, uncover the bottom back cover and there you see compressor, condenser fan and other good stuff. there you unscrew the nut in front of the condenser fan and remove the fan, then it expose the two screws that holding the fan motor, remove these screws and take out the motor. and just install the new fan motor kit in and there you have it. plug it back to the wall and there it goes

Ice Maker quit working

  • Customer: David from Castalia, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Had to Test Seloind. It Was OK. Then tested Motor Motor For Ice Maker. It Was Bad. Went Online Looked Up Parts For My Unit. They Were Shipped in a Timely Manner, only a few days. Installed parts in less than 15 minutes. Went very easy. Thank You

Both the freezer and bottom of refrig too hot

  • Customer: Marcia from Kansas, OK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Was very simple once I found out where the defrost timer was located. I had a friend walking me through trying to find the location on the phone. Not all models have them in the same place. Once the part was located all I had to do was remove the cover, unplug the old one and plug the new one in just the way the old one came off. The black wire was easy to locate on the old and just matched it up. Put the cover back on and plugged it in. It was no time till I started feeling it cool. Checked both top and bottom with thermomater and it was where it should be within 12 hours. I am happy and using it again. Was almost ready to throw it out. Did not know it was so cheap to fix one. Nothing anyone can't handle. If this woman can do it anyone can.

Broken ice bin auger

  • Customer: Howard from Parrish, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After watching a video on you tube, the repair was very simple and easy.

Very noisy when condensor fan came on

  • Customer: manuel from wilmington, DE
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I've tried ordering the part from Sears and they told me it will take about 7 days for the part to arrive, some other place said it will overnite for extra money. So I've ordered the part from Part Select at a good price and prompt delivery. once the part arrive installing the part so so easy cause it had easy to follow instructions.

the ice bin auger had broken

  • Customer: cynthia denise from tullahoma, TN
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
i used the instructions that came with the part and it was really simple. thank you very much. it saved me a HUGH repair bill.we use alot of crushed ice and the part shipped in 2 days. thank you.C.D.L.

Ice door got freezed

  • Customer: Nivia from Miami, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
With the flat screwdrivers, table knife or something to pull the front cover, is not easy but it will come out, patient and kepp trying until you made it, the rest is easy.
All Instructions for the RS22AQXMQ01
1,006-1,020 of 1,407