Models > RS22AQXMQ01 > Instructions

RS22AQXMQ01 Roper Refrigerator - Instructions

All installation instructions for RS22AQXMQ01 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RS22AQXMQ01
991-1005 of 1317
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Runs & Does Not Cut Off, Freezes Everthing

  • Customer: Charles from Waco TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched The Movie, Told Wife What To Do

Had to completely remove the ice maker in order to install the replacement part

  • Customer: Leonard W from Roseburg OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Sorry for delay in writing. Part I ordered arrived two days ago and it was exactly what I needed. Knowing that there will be problems even with the smallest job I procrastinated starting. When I did start this morning I foud I had to completely remove the ice maker and disassemble it in order to install the water fill cup bracket. The challenge was reassembling the unit. Not hard for an experienced repairman but a challenge for layman. Everything is thing is back to gether now and power on cooling down the refrigerator. Won't know how successful it was until turn on water and ice is formed. If it works this saved $75 just to get a Sears repairman to come out and tell me what would be needed to fix the refrigerator and $1,000 if I had to buy a new refrigerator. Extremely satisfied with service I received. Thank you.

PART WHERE ICE MAKER ARM FIT IN BROKE OFF

  • Customer: Yvonne from Worthington IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
TOOK ICE MAKER OUT ALL TOGETHER WE REMOVED 4 TO 5 SCREWS HAD TO REMOVE AXEL TO GET THE BROKEN PIECE OUT AND NEW ONE IN MY HUSBAND SAID IT WAS EASY IN AND OUT IN ABOUT 15 MINUTES SAVED ABOUT 150.00 THANKS PARTSLECT

Refrigerator freezer would freeze but cold box not very cold

  • Customer: Jesus from Taft CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
I went on line to find the symptoms for what I was experiencing and went to web and entered the "KSRA" alphas and this list came up. I followed the explanation on video and it was identical. Good stuff.

Noisy evap. fan

  • Customer: Robert G. from Glendale AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed cardboard, Removed 4 bracket mounting screws, Removed plug, Removed screws securing motor to bracket. . Installed new motor on bracket, Installed fan on motor shaft , installed new pigtail on motor, Installed new assembled motor and bracket, Hooked up pigtail to electric supply, Installed cardboard, Plugged in to power supply and Voila, not even one foul word during the whole process. Note: watch the factory video. Thanks.

Fridge and freezer were warm.

  • Customer: Michael from North Attleboro MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The evaporator gan motor would work sometimes, but not always, so it took a while to be sure this was the problem. First ruled out thermostat and defrost timer. Also observed build up of ice on coils, so I knew compressor was working. Once I isolated problem to evaporator fan ( by observing stuck once, and seeing how it didn't spin freely) replacement was easy. In fact, since we were able to keep the unit running by watching the old fan and ensuring it was working while waiting for the new one to arrive, I was able to swap them out, plug unit back in and start it up before the ice in the bin even had time to melt! This repair saved me hundreds in repairs, and even more if I had to buy a new fridge, because the new units are too tall for my kitchen space.

Freezer worked, Fridge side struggled to stay cool

  • Customer: Brad from Springboro OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Turn off power. Remove freezer shelves. Remove six screws on the back of the freezer. Slide out metal piece. Pop off plastic fan piece. Remove motor mount by squeezing metal bracket. Take off wires... Do reverse... Attach wires to new motor, install motor (may have to also use the clear rubber piece from the old motor which keeps the motor in place). Push fan blade back on. Screw in metal plate, turn on power. Good videos on YouTube as well.

Freezer iced over, water leaking into refridgerator

  • Customer: Jennifer from Cincinnati OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
My fridge is a little different from the video model. The Controls in the fridge are located on an "arm" which swings down when the two screws are removed from the sides. It was not necessary to remove a front plate or knobs. However, I found when I got in to it that the old timer was not held by screws, but by plstic posts which had these "speed nuts" on them. This is a little metal plate which fits over the plastic post and bends to lock it in place. When you try to remove it, it acts like a barb, holding the little sucker on. I ended up bending the ends of those little suckers up tight against the post and twisting and pulling with needle-nose pliers. I broke one post like others before me commented, but one stayed intact. The only break at the top, so there ie still post left to hold the new timer. Once it was off, I was able to replace easily. The directions for choosing the right prong were a little confusing, but follow your gut and go with the wire colors. My schematic found in the bottom of the fridge did not look like any of the drawings, but I could match the wire colors. I also asked "Just Ask" for help, to make sure. My gut instinct was right. My fridge is now working again beautifully. If a housewife with no appliance repair knowledge can do it, so can you. I fixed my dryer with PartSelect too!I will never call another repair man until I have checked this site to see if I can do it myself. Bet I have saved $600 so far at least!

Both the freezer and bottom of refrig too hot

  • Customer: Marcia from Kansas OK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Was very simple once I found out where the defrost timer was located. I had a friend walking me through trying to find the location on the phone. Not all models have them in the same place. Once the part was located all I had to do was remove the cover, unplug the old one and plug the new one in just the way the old one came off. The black wire was easy to locate on the old and just matched it up. Put the cover back on and plugged it in. It was no time till I started feeling it cool. Checked both top and bottom with thermomater and it was where it should be within 12 hours. I am happy and using it again. Was almost ready to throw it out. Did not know it was so cheap to fix one. Nothing anyone can't handle. If this woman can do it anyone can.

frosted evaperator

  • Customer: Burton from Mount ShaSTA CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I was a Sears repair man for fourty eight years , so I don"t think I should say how easy this was.

Freezer was too cold and refrigerator was too warm

  • Customer: Jolinda from Eau Claire WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After receiving the part, I watched the installation video on the PartSelect website. The step by step demonstration was excellent. I felt confident I could do it myself after watching the video just once, and utilizing the written instructions that came with the part. The installation went smoothly, and my refrigerator is functioning correctly again. Best of all, I did not have to go through the hassle and expense of hiring a repair person!

not cooling could hear a clicking noise

  • Customer: Deborah from Elkton MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
With the help of the website I was able to verify that the part I removed (in the area of the clicking sound) was probably the part required for replacement. I ordered it, installed it... IT WORKS (I knew it the moment I plugged in the power cord and heard the compressor kick on). Saved me from buying a new fridge or calling a repairman. I'm a 58 year old woman with no appliance experience. I watched the videos and installed the part without any trouble. Thank you PartSelect for your easy to use website instructions and helpful hints.

frig and freezer too warm--food spoiled

  • Customer: NANCY from CINCINNATI OH
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
son put part on--must be something else causing problem--better but not completely fixed because the frig side is 40 again and still getting warmer--any ideas!!

Ice maker quite working

  • Customer: Cleave from Denton TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video. And it was a big help

Ordered ejector arm.

  • Customer: Joyce from Springfield MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
No instructions with part. Found a picture on line and changed the arm, but it didn't fix the problem. Fairly easy after figured out what needed to be done to get to the part.
All Instructions for the RS22AQXMQ01
991-1005 of 1317