Models > RS22AQXMQ01 > Instructions

RS22AQXMQ01 Roper Refrigerator - Instructions

All installation instructions for RS22AQXMQ01 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RS22AQXMQ01
961-975 of 1,392
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

old ice maker did not work at all.

  • Customer: Donavan from Raleigh NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug refrigerator and turn water supple off. Remove three mounting mounting screws and unplug the old ice maker.(there is a latch on the plug to release it) Remove shutoff arm from old unit or if ordered seperatly with the ice maker, install shutoff arm on the new unit. Plug the new unit in (latch will snap into place when plug is properly seated.) Install the bottom screw (leave screws loose until all are started in the orginal holes). Tighten screws and you are done. Turn the water on and plug refrigerator in. After about an hour or two the ice maker will be cold enough to start making ice. In about five hours or so you will see the first ice cubes!!!!

plastic stopper came off arm

  • Customer: TinTina from Bruce WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
with a mirror to see the small hole on the front side of the icemaker.... very simple, took 1 minute

Replace Ice Maker & Shut Off Arm

  • Customer: Charles from Spokane Valley WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Installation went fairly smooth, only problem was because it is a side by side freezer space was a little tight and screws were hard to see, but other than that works fine.

Ice door hinge was broke and not letting door close building up ice between door and ice maker.

  • Customer: billy from cleveland TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Popped the cover off took panal off to access ice door screws.Removed old parts and replaced with new kit.Works fine now.

Ice door broken letting warm air into freezer

  • Customer: Lou from Key Largo FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After I ordered the parts, which was very easy to do using this website I read the other comments in reference to this repair. I am in agreement with anyone that said patience is important! The repair went about as expected, the only thing I had to do different was, after I assembled the door, it would not activate. I checked the microswitches for the ice dispenser and found that the arm on the glass bracket was not hitting the switches. I shaved off part of the horn on the back of the arm and that solved the problem!

Door to the ice shute broken with worn out parts.

  • Customer: Edward from San Antonio TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Took two screwdrivers and inserted bottom of bezel pryed up and out gently. Removed (4) screws and unpluged (3) electronic plugs removing the circuit board. After you remove bezel & circuit board you have a chance to see what you are doing and get to the problem area with more ease. Remove old parts and reverse it putting the new parts. Process is very simple just pay attention to the order everything was removed. On my frig one of the plastic ears that hold the pin which holds the spring and door was broke. The piece I needed was no longer avaliable. I had to use a piece of the plastic from the old parts I removed, drilled a hole the size of the pin in it and glued it to the broken off ear. Put everything back together and I am pleased to say that everything works fine! So you might need to go a little MacGyver on it. All in all very simple fix.

Ice door got freezed

  • Customer: Nivia from Miami FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
With the flat screwdrivers, table knife or something to pull the front cover, is not easy but it will come out, patient and kepp trying until you made it, the rest is easy.

Ice door leaking air into freezer

  • Customer: Richard from Jamesport NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the lead of David from Chesterfield in prying off out cover, unplugging it and setting it aside. Unscrewed and pulled out next assemply, and taped it above work area to avoid having to unplug. The pried pulled out pin to right holding ice door hinge to remove old unit. (Notice which way the spring faces before removing!) Unplugged it. Ended up taking off push-dispenser handle (one screw on right) to get easier access. Then reinserted long pin being careful to have spring with two long tongs pointing down. Then put everything back together. USE ALL PARTS!

Broken roller wheels

  • Customer: Joseph from Tyrone PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Followed the instructions on package, went extremely well, with no problems what so ever! Thanks so much for the part and how to do list!

NO LIGHT

  • Customer: Mary from Jefferson Township PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
TOOK SOCKET OUT AND REPLACE IT WITH NEW ONE. VERY EASY. W SAVED ALOT OF MONEY DOING IT OURSELF.

Protective cover for bulb had melted

  • Customer: Lee from Brooklyn NY
  • Difficulty: Very Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

Broken Water Nozzle at Door

  • Customer: Chris from Brentwood TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fitting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!

The ice maker drum was totally broken and would not allow ice to drop and the crush ice mode would not work.

  • Customer: MICHAEL from CORDOVA TN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I printed your diagram of the complete assembly for reference when installing the new part. I was able to get the part number from the diagram and ordered it online. I received the new part in 2 days. I removed the ice from the ice maker's bin and kept it in the freezer. I removed the old drum and auger from the ice maker assembly and installed the new drum #4388736. I looked at your diagram to make sure I had all of the blades in their right orientation. After the drum and auger assembly was installed, I placed the ice that I had saved into the ice bin and slide it back into place. I then tested if the assembly would now drop ice and also if it would crush the ice, which i do not use very opten, because I know that using the ice crush mode will prematurely wear the drum assembly. The drum and auger gets much more stress when it is crushing ice. After the icemaker worked flawlessly, I rolled the refrigerator back into its regular position along side the cabinets. I was very pleased with the part and the excellent service that PartSelect.com provided. The price was less than I thought I would have to pay. Also, the company provides most of the individual parts of the ice maker assembly. Normally, when I would shop at a designated Whirlpool distributor, I would have to purchase the entire assembly costing 3 or 4 times higher than the price of the individual part. I, will now, always purchase my parts from PartSelect.com.

Would not feed

  • Customer: Ron from Natrona Heights PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Found auger was broken. Also found the ice cubes seemed too big and not breaking apart after the ice maker would cycle and dump in to the bucket. So I adjusted the ice cubes water feed timer making the cubes smaller and they are working real good through the auger now.Thanks for delivering the part so fast.........

frig and freezer too warm--food spoiled

  • Customer: NANCY from CINCINNATI OH
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
son put part on--must be something else causing problem--better but not completely fixed because the frig side is 40 again and still getting warmer--any ideas!!
All Instructions for the RS22AQXMQ01
961-975 of 1,392