Models > RS22AQXMQ00 > Instructions

RS22AQXMQ00 Roper Refrigerator - Instructions

All installation instructions for RS22AQXMQ00 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RS22AQXMQ00
1,096-1,110 of 1,470
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice maker failed tp produce ice

  • Customer: Peter from Punta Gorda FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed three screws. Discount wire harness. Reverse proceedure for installation.

old icemaker went bad the form tray bubbled up and held cubes in place that stripped the drive gears at the motor end

  • Customer: Jon from Barnegat NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watch the u-tube video first ,Then read instructions that came with new unit ! so darn easy. unplug fridge, remove ice bin, clean and dry bin before putting back in service! stick flashlight in freezer loosen 2 top screws remove 1 bottom screw, unmount unit, unplug wire harness, remove icemaker and put on table, close freezer door !! , Remove sensor arm from old unit in down position and install in new unit. plug in new unit and reattach in freezer. replace ice bin and plug in fridge, that's it!, It took about 2 hours for the icemaker thermostat to say OK lets go had a load of ice in aprox 3 hours from finish. piece of cake. Jon

Icemaker had started leaking water into ice bin upon filling.

  • Customer: John from Colombia MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the online video and it looked just too simple.....so when I got the new unit I did not have to even change the wiring harness and I was totally surprised that the change could be so simple and easy! Trick is to follow the video instructions and DO NOT take out the two top screws but just loosen them enough to lift up the old unit and remove it! Cannot believe it could be that simple and easy.

failing icemaker

  • Customer: geoffrey from flagler beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Exactly as instructed by video on your site. The replacement took 10 minutes. thankyou Partselect.

my ice maker was leaking into my ice bucket freezing it into a solid chunk

  • Customer: Becky from Perryton TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the installation video and did just like it said. It was pretty easy. My ice maker is working once again, and I'm pretty proud!

Ice maker was leaking

  • Customer: Nick from Duck NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Really couldn't be easier. Loosen 3 screws that are easy to find. Disconnect the quick connect wiring harness. Now you have the old unit out. Take out the wire that tells if there is too much ice from the old unit and put it on the new one ( this was the hardest part of the project) Hook up the new wiring connector and hook it on the screws and tighten it up. Viola, your done. No messing with the water. Took me 5 minutes and I've never done it before.

ice maker did not function

  • Customer: Gary from Garfield GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
watched video, followed the instructions and everything fell into place. since the wiring harness was not removable, I disconnected the harness from the the old unit and hooked it up to the new unit. put every thing back together,plugged in the power cord and turned on the water. water filled the ice maker and ice appeared in about an hour.

ice maker was leaking and not making correctly making ice cubes

  • Customer: Melba from Aberdeen MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
ice cubes are now being made properly and there is no more leaking.

Ice tray was overflowing with water, when refilled.

  • Customer: Kelly from West Valley UT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench set
  • 0 of 0 people found this instruction helpful
First replaced the Dual Inlet Valve, because this seems to be the most likely part to fail, (this was not the cause, but I still recommend replacing it, due to the high failure rate when over 10 years old.) Then pulled the IceMaker and inspected the gear that controls timing for refill of the ice cube tray. Found that the contact that is responcible for timing of refill, had extended the length of the contact with carbon, (from braking contact at the end of of the fill cycle) creating a short black trail of carbon, which had become conductive and was the reason for the over fill of the ice cube tray. Once the new tray was functioning, the issue vanished.

ISCLES HANGING FROM UNDERSIDE OF ICEMAKER & FROZEN "PUDLES" IN THE ICE BIN.

  • Customer: NEAL from boyton beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
PREVIOUS TO INSTALLING THE NEW ICE MAKER - I REPLACED THE DUAL INLET WATER VALVE PER THE INSTRUCTION VIDEO I FOUND @ PARTSELECT WEBSITE. THAT DID NOT SOLVE THE PROBLEM <> I ALSO ADJUSTED THE TIMER ON THE OLD ICE MAKER DOWN - PER ANOTHER VIDEO / WHICH ALSO DID NOT SOLVE THE PROBLEM. THEN I VIEWED THE VIDEO ON ICEMAKER REPLACEMENT - ORDERED THE ICE MAKER & 3 DAYS AND 15 MINUTES LATER <> THE PROBLEM WAS FIXED ! THIS WEB SITE IS "FANTASTIC" ! THANKYOU PARTSELECT FOR YOUR ASSISTANCE ! ! !

Water was pouring into ice bucket instead of filling the ice maker.

  • Customer: Kim from Killeen TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I replaced the ice maker with a new one. All part were included. The cost was about $200.00 cheaper than what the repair person wanted.

Ice maker would fill with water and make ice but would not dispense ice.

  • Customer: Terry from Plano TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Ice maker is held on by two clips and one screw. Removed old ice maker and unplugged wiring harness. It appeared normal. Since it was 15 years old and a brand new one was only a little more than $100 I decided to just replace it. Shopped online and got best price here. Delivered promptly. Item description said it did not come with wiring harness, but mine came with three different ones. However my wiring harness had a different molded plastic connector where it is plugged into the back of the freezer so I could not just pop it off and pop in the new one. Instead I had to reuse my old one. No problem, since the harness was not damaged anyway. Also I had to reposition the harness clip on the new ice maker and remove the plastic tab on the bottom and re use the tab from my existing ice maker. The tab on the new ice maker would not line up with the hole in the freezer. All in all it took about 10 minutes total to switch the two units out. Extremely simple job, do not pay someone to do this for you.

replace ice maker in refigarator

  • Customer: Jimmy from Strong AR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
very easy two small screws, no problems

Ice maker stopped working

  • Customer: JOHN from Bronx NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair man came out and said the Ice Maker is broken.He said to call him when I get the part but after looking at the video it took 10 minutes to Install. If you can use a screw driver this part is a piece of cake. Oh don't forget to unplug the frig. God Luck John Bronx NY

ice maker got out of time water frooze with paddle down in the the ice tried to dump and spin (broke ) the timer gear off

  • Customer: Herbert from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
turned off power unscrewed all the screw that mount ice maker, used flat head to release the clip on the wire harness, took out and exchanged the overfill wire, plugged the new unit in at wire harness, lined up and leveled ice maker tighten all the mounting screws, very simple repair i am very happy that you still had the orginal (OEM) ice maker, thanks Herb
All Instructions for the RS22AQXMQ00
1,096-1,110 of 1,470