RS22AQXKQ04 Roper Refrigerator - Instructions

un-plug the power cord. remove both control knobs. pry off the cover. remove 1 screw on the right and left with the nut driver. remove two screws in back with the nut driver. remove the screw holding thermostat in place, loosen screw holding the left side of the l plate. lift thermostat up and remove two nut driver screws. remove the temperature sensing line from holding device. Remove cover down the side of refrigerator and the cover over the sensor (in back corner) carefully remove the sensor line. Carefully bend the sensor tube into the shape of the removed part(do not kink)install the new part in the reverse order of removing.. Use flat blade screw driver to press sensor line into the snaps. This was one of the easiest repairs I have ever completed.

I followed the UTube video step by step, pausing at each section made repair very easy. Watching the video is a definite must!

Simply done !

Exactly how the instructional video described it to be. No surprises what so ever. Ended up not being the culprit to my problem. Ordered and installed a bi-metal defrost timer. Also, extremely easy as the instructional video described it to be. Partselect is an awesome resource for knowledge and quality products with very reasonable prices.

Spent six hours melting the ice berg, twenty minutes cleaning things up and ten minutes replacing the ice maker. The video was great the only piece of information that was missing was a statement that it may that several hours for ice to be produced. Thanks for the prompt and courteous support during ordering, a good product and support video.

Exactly how the part select video described it. Threw a little curve ball figuring out which timer setting to set it to. But the instructions provided with defrost timer walked me right through it. No problem. After installing part nothing happened for about ten minutes, which had me second guessing each and every step. Then, like magic, cold air began blowing. What a relief. Thanks so much, love this site. Refrigerator works like new!

I order the suspect part before pulling out the ice tray and whole ice maker for inspection. As it turns out my ice tray was peeling and all gunked up and I needed a new one. I suggest in the case of ice maker issues that you pull the entire ice maker before ordering what appears to be the troubled part. I had to replace the whole ice maker which was not really that much more money than just the part.

I looked at the video that part select send. I did exactly what it said to do,and now my refrigerator is working just great. And the noise is gone. I thank you so much for your help. And I'm a 64 year old women thats how easy it was.

1. Cleared all the food items off the broken shelf. 2. Removed the old shelf. 3. Removed the new shelf from the shipping box. 4. Inserted the new shelf. 5. Replaced food items.

1. Remove the ice-maker/water dispenser cover plate located on the freezer door, by: inserting a putty knife blade at the bottom and freeing up the two retainer tabs; then pushing up. (note: be careful pulling the cover plate, there are many electrical connections on the back).

2. Note the electrical connections on the back of the cover plate and locate the connect close to the inside of the freezer door and disconnect it. (Note: this is much easier than pulling each wire off its connection point and then having to remember which color coded wire went where).

3. Carefully work the door hinge pin back out to the right and remove it and the hinge (Note: in my case the pin was already half way out so the old door couldn't close - and since this model door had a heater which came on because the door was misaligned there was constant flow of warm upwards causing ice to melt, run down and re freeze thus making the door difficult to open).

4. Unscrew the single her head screw holding the small metal piece to the right that retains the know upon which the outer door frame turns. Move the frame to the right to free it and work it out if the way. You now have access to the ice-maker door and hinge pin assy.

Watch the Video! My reefer's ice door/spring 'pin' removal and installation is different than what is shown in the video. That is, my spring 'pin' looks more like a long nail (with a head on the right end). After inserting the left end of the pin into the hole, the head end drops down into a notch, which makes removal and installation easier than what is shown in the video. It is much easier to reinstall everything if the 'ice-chute' is installed first. Then, maneuver the ice door assembly into place and install the pin. I used Blue masking tape to hold the control panel up and out of the way. This is the second ice-door repair since I've had this refrigerator. It seems to occur with 'heavy' use of "crushed" ice. Some crushed ice backs up behind the ice door/flap, jams/holds the flap open, letting warm air into the freezer, causing the crushed ice to freeze into a big 'clump' of ice (too big to come out of the chute, and causes frost in the freezer. If you get a clog like this, I suggest removing the ice "bin" and gently clearing the clog from the top side of the ice chute with tongs or needle nose pliers. If you try to remove the clog from the bottom of the ice chute, the door becomes dislodged or breaks...

watched video, followed the instructions and everything fell into place. since the wiring harness was not removable, I disconnected the harness from the the old unit and hooked it up to the new unit. put every thing back together,plugged in the power cord and turned on the water. water filled the ice maker and ice appeared in about an hour.

ice cubes are now being made properly and there is no more leaking.

I am a woman, not mechanically handy, but set my mind to do this myself. The part came in 2 days. I watched the video and had it in done within minutes. Very easy! A few scews and follow video.

Thermostat replacement