RS22AQXFN00 Roper Refrigerator - Instructions

I went on line to find the symptoms for what I was experiencing and went to web and entered the "KSRA" alphas and this list came up. I followed the explanation on video and it was identical. Good stuff.

Exactly as instructed by video on your site. The replacement took 10 minutes. thankyou Partselect.

I watched a couple of videos on your website about how to install a couple of parts that could possibly be causing the problem. Then I went and took the cover off of the area where the ice and water dispenser are in the door. I could tell from watching the videos which parts to look at to see where the problem might be. I figured out which part it was because I could see where it was broken. I then ordered the part. After I received the part I watched the videos again and then did the repair. VOILA! It worked. I put everything back together and the water dispenser was working. I was so pleased that I didn't have to call a repair man and I actually fixed it myself! My husband was so glad too.

I followed the video instructions to replace the ice maker controller. Works like new. Each to order from website, part arrived in 3 days. I'll certainly order from partselect.com again.

The video provided excellent instructions on how to to this job. The hard part was removing the keeper ring so that the auger assembly could be separted from its housing.

Watched the online video and it looked just too simple.....so when I got the new unit I did not have to even change the wiring harness and I was totally surprised that the change could be so simple and easy! Trick is to follow the video instructions and DO NOT take out the two top screws but just loosen them enough to lift up the old unit and remove it! Cannot believe it could be that simple and easy.

Technically, the repair did not require specialized knowledge. However, replacement of the motor required some effort. Because the motor is located at the bottom of the unit in an area with copper tubing & wiring hindering access it was physically difficult to remove and then replace the motor. A problem arose because the shaft on the replacement motor was larger than the original motor's. Thus the fan would not fit on the new motor. Luckily, I found a fan locally that fit the motor. It would be very helpful if a fan was included in the motor kit. The ref. is now running smoothly

Very simple repair. Followed the video instructions. Simply removed a few screws and nuthead screws. Removed the cover plates. Removed the old thermostat switch. Removed the plastics tubing over the temp sensor probe. Put the plastic tubing on the new sensor probe, ( rubbing a slight amount of vegetable oil on the probe to allow the tube to slide on easier,). Reinstalled the temp probe. Reinstalled the new switch. Connected the wires to the switch. Reinstalled the cover plates and screws. And the job was complete. Almost took me longer to write this out, than it did to complete the project. Hey, it was an easy fix.

Got the main bolts off and unplugged and removed the ice maker. Had to remove all parts and rebuild it on the new mold. Was more complex than I thought but was able to get it done. Note where everything was as you take it off and you'll do fine.

Removed the cover from Thermostate, removed the wires, and screws holding old thermostate, reversed instulation with the new thermostat, pretty simple.

I removed the top door hinge cover, removed the top hinge, pulled the refrigerator door off, layed it on the floor, removed the door cams, installed the new door cams, replaced the doo and top hinge and hinge cover. If you have this problem with your refrigerator door, be sure to replace the upper and lower cam.

removed front trim, removed plastic bracket, removed broken ice guide, installed new ice guide, installed removed items in reverse order, finished.

Googled for a solution to how to fix a refrigerator door that would not close. Was directed to a video from PartSelect. Was wrong brand, but I got the general idea. Then, I looked up a refrigerator repair for Whirlpool. Called PartSelect with my model number and ordered a Cam Kit. Total cost shipped $20. Arrived in two days during the Holidays! Nice! (Ordered 12/23, Arrived 12/26). Opened package, fired the video up. Fixed in 15 minutes. Amazing!

Removed screws from the back of the part in the fridge. Pulled old part out. Measured the old part. Cut new part to fit. Replaced new part and tightened the screws. Worked perfectly.

Talked to local appliance repair tech, who explained how to manually turn timer with a screw driver and listen to the switch go from on to off.