Models > RK767G*D2 > Instructions

RK767G*D2 Hotpoint Oven - Instructions

All installation instructions for RK767G*D2 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RK767G*D2
571-585 of 603
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bottom element had burned through.

  • Customer: David from Atlanta GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Quarter inch socket was all that was required. The plate that covers the slot where the element threads through from the rear was smaller than what was on the original element, and it took a few attempts before it was secured properly to cover the opening, but other than that, it was a snap. I estimate that I saved well over $200.

broil element failure

  • Customer: Glenn from Plano TX
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Unscrew 4 easy nuts and 1 most difficult nut, gently pull both long and short wires, at this point assure the wife that you did turn off the power.You may wish to attach a cord to short wire as it wants to vanish into the rear bowels of the oven On instruction of the wife clean the oven. Reverse dismantling procedure. Switch oven on. Bask in wives praise.

Burnt element

  • Customer: Lawrence from Burlington VT
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed old parts with nut driver and installed new part. Don't forget to unplug before working on unit. Very easy repair can be done by anyone who can read and understand instructions

exchanging broiler element

  • Customer: Beverlee from Mill Valley CA
  • Difficulty: Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Even though my sons offered to do the repair, I opted to hire an appliance technician to do it and it took him at least 45 mins. with his experience and tools. apparently the inside wall wires were shorter and more difficult to access and grip and I'm glad I did. It should last another 20 years and I'll be dead!

Bulb replacement

  • Customer: Judith from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover...released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Lower baking element was not working

  • Customer: Marie from Princeton Junction NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
You must turn off the power to the oven since it's directly wired into the electric. One person holds the flashlight while the other removes two nuts, then two screws. Tight space to work in with head in oven. Tricky getting the screws back in and them making sure the unit is centered in the space when tightening the screws. Turn power back on when done. Works like a charm.

I replaced the lower heating element of the oven.

  • Customer: Allen from Naperville IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After removing the two oven racks, sitting on a low stool positioned on the side of the oven door, and placing a magnetic light on the oven wall, it was easy and comfortable to change out the heating element. A magnetic screw driver is helpful. Two screws had to be removed to free the element from the rear wall of the oven. Then two small screws needed to be unscrewed to free the terminals from the oven-wire terminals. The reverse procedure was followed to install the replacement heating element.

Oven element no longer heated due to broken element

  • Customer: Kent from OLCOTT NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Unplug oven, and remove the wiring cover on the back of the oven, unscreen the screws attaching the wires to the element leads and pull the element out. Put new element in and screw on the wires and reinstall the wiring cover. All done less than 15 minutes.

The heating element needed to be replaced.

  • Customer: Karlene from St. Louis MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I chickened out and had a friend do it for me so it was real easy.

Oven Bake element burned out

  • Customer: Donna from Rogers AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Repair was very easy. The instructions on Partselect.com with the item ordered described exactly what to do. I followed the instructions and it works great. Used socket wrench to remove the two screws holding the bake element bracket to the oven wall. Pulled the element out. Used a screwdriver to remove the wires from the old bake element. Use a screwdriver to put the new wires on the new bake element. Pushed the bake element back into place. Used a socket wrench to tighten the oven bracket to the oven wall. Done. Turned on the oven. Worked Great!!!.

Broil Element burned out

  • Customer: Myer from Cleveland GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed old element, checked continuity and element was bad, Fit new element and everything was good. No problem except my arms were not long enough!! Repairs took about 15 minutes.

Bake element broke while in use

  • Customer: Dominic from Grand Rapids MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Was looking at $1000 to replace range. Found the part for $30 with shipping. Just need to pull range out and have access to front and rear. AND UNPLUG FROM OUTLET (I also cut power at the box. That's just me) From rear, remove 2 screws holding on vertical cover and remove cover. Remove screws holding wires to element leads. From the front, open door 1/4 way then lift off of hinges. This makes reaching into the oven box easier. Remove two screws holding element to the back wall and remove. Insert new element. Go to back and use new screws that came with element to connect wires Make sure insulation is in place and replace cover. From the front re-connect element to back wall and make sure both feet are level on oven floor before tightening. Put oven door back on, plug in and test. Once tested push range back into place. Whole thing took 20 minutes.

Element burned out

  • Customer: Anthony from Tully NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Turned off circuit breaker (220) removed old element - replaced with new element.Very Easy - inexpensive and arrived fast.ordering was easy by using serial number.

the baking element did not work as it had a hole in it( burned out)

  • Customer: Ronald from Geneseo NY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
the screw driver I used had several different nut driver sizes so that was the only tool I used. I took the 2 screws that held the element inplace and then there were 2 more that held the wires on to element.

broiler element burnt thru

  • Customer: Larry from Mendota IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
TURN OFF POWER , remove oven door & oven wire racks, remove two retaining screws in back of coil and pull the burnt coil foward enough to remove the screws that hold the wires to the coil. You may have to drop one side of the front support bracket to move coil forward.Fasten the new coil to the broiler wires with the new screws provided. Push the new coil back into place being careful not to pinch the wires in the opening. Refasten coil to the oven back with existing screws that you removed. Refasten front support.Put racks back in and put door back on.Easy fix! Easy to order, easy to install and came within days from order date. Very pleased with whole thing.
All Instructions for the RK767G*D2
571-585 of 603