RK524GP2BG Hotpoint Wall Oven - Instructions

first, made sure circuit breaker was off
second, used nut driver to remove 2 screws on old element, pulled it from the back of the oven
third, removed 2 wires from old element (spade connectors)
fourth, connected new element and pushed back into oven.
fifth, reinstalled 2 screws securing new element

this was all done by my 15 yr old son under my supervision.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches, but I had not turned off the power.
So, I shorted out one of the wires. Then I turned off the power but was afraid to go any farther.
An appliance repairman was at my house that day fixing my dryer seal. He was able to pull the wires through the insulation successfully and install the broiler element. He did not charge me any extra for this little extra job. But I learned my lesson. Cut the power before you begin! He told me that I could have wound up with a much bigger repair if the short had been in the wire that is connected to the control panel of the oven. I was very lucky!

at first thought the seal would just slide out and the same for the replacement. when I realized that this was not the case and began to wonder what....? I saw the screws at top and bottom, took them off and voila the inner shell moved forward enough to take out the old, slide in the new, push in, replace the screws and back to a happy wife with an oven that can bake correctly again

FIRST MAKE SURE THE OVEN IS OFF!!!! I chose to shut it off at the breaker panel. Remove the two screws that attaches the broiler element to the oven. Gently pull it out. Unplug the two cable wires that are attached. Replace it and install the same way.

removed 4 screws of the back fan cover, then removed the two screws holding the element and disconnected the slip-on electrical wire connections. replaced enement and cover in reverse. this was all done after i cut power at circut breaker duhh

I removed the two mounting screws then pulled the element forward and disconnected the two element screws. I reversed the process to install the new one/ this oven is over 30yrs old.

If I'd had the Nut driver, it would have taken 15 -20 minutes or less. Went to Ace Hardware, bought the nut driver for $4.99.

Turn off the power at the box! Turn off the oven as well. Four screws total. Two to hold it in place and two that connect the element to the source.

First I removed the two screws that hold the element in place. I pulled the element out about 2 inches. Two more screws connect the element wires. I disconnected the element, threw it away, then connected the new element. I put the element in place, then replaced the screws that connect the power. Finally, I replaced the screws that hold the element in place.

Kimberly, El Cerrito, California

Removed the oven racks, removed screws holding element hanging support from roof of oven, removed screws holding plate of element to rear of oven. CAREFULLY worked element loose from back of oven and gently alternated pulling each side of element (near the base) until connecting wires came free of insulating batting. Pull too hard and the connecting wires can break loose and disappear behind the batting. Once freed, disconnected both wires with socket (use pliers for extra grip on flat part of connectors, if necessary), removed element, braced new element on bottom of oven, aligning connectors to now-free wires. Re-attached with the new screws that came with the element (attachment points on element are threaded; do not reuse old screws as the threads may not match), gently re-inserted element into insulating batting at rear of oven, reattached hanging support, then replaced element plate screws.

Can be difficult to work in small, deep ovens....many oven doors can be removed. If so, remove oven door and use a chair as a support...lie on your back on the chair and hang your head and arms in the oven.

I removed the screws holding the old element in place, then pulled it out a few inches from the back oven wall. Then I pulled the wires away from the old baking element (pulled off easily), and being careful to keep the wires on the same sides as before, pushed the new element on to the wires. It was then just a matter of inserting the wires and insulation back into the opening and tightening the screws. Simple!

scissors and opened bag. determined that all three knobs were identical. aligned slots on each knob with flanges on each shaft.
snapped each knob into place.
Did a happy dance of empowerment around the kitchen. ( knobs had been broken for at least 5 years).
used timer to avoid burning christmas cookies.
Have a Merry one!!!

Snapped in the clip

It was very simple.. first turn off the electricity... next take out the two screws holding the element to the back of the oven... then pull the two plugs apart( male and female ends) ... throw away old part.
put new part in by plugging the male and female ends back together... push back into oven back.. get all insulation back in... put two old screws back in to secure... done.. turn on power...
don't be afraid.. it was very, very easy.

Remove the screws inside the oven holding the back of the element to the rear wall of the oven. These scrrews are a square drive. Pull element forward and remove 2 screws that hold wires in place. Both sets of screws needed to be replaced with a different size. Reverse order to install.

The two dollar socket set from Xmas 20 years ago had the right size socket..

Long arms are advisable.

The lower element still plugged in while the upper wires were just hanging there surrounded with fluffy white insulation fuzz, I wondered, " Could I bake a potato for my yearning and hungry family?"

When I explained the situation to my retired father in Arizona he said simply, "I wouldn't."

The new element popped in. It got really red, and, kinda like watching my toaster toast, the show was pretty much over after it heated up.

Shalom and Merry Christmas Folks!

I first removed the broken element by removing the two hexhead screws on either side of the element bracket. Then I gently pulled the wires through the opening and removed two more screws that attached the wiring to the element. I then compared the new and old elements and found a few differences.

First, the screw holes where the wires connect to the element were tiny in the new element, about a third the size of the holes in the old one. Secondly, the mounting bracket was not as long as the original, and the holes to mount it to the back of the oven are located at the top of the bracket, instead of the sides.

Since this was the only element that I have found, that comes close to the original, I decided to make it work.

I took my drill and a small bit and bored out the screw holes, just enough to get a self taping screw to fit and reconnected the wires.

Now I'm not sure that I would recomment the next step to anyone, but I did this: I held the new bracket against the back of the oven and drilled new holes to match the new bracket, and again used self tapping screws. The reason that I don't encourage this is that the new bracket fits just inside of the old opening, but the insulation cannot be seen as long as the element does not get moved. I then plugged the original bracket holes with the original hex head screws.

It took a little more time and effort than I had expected, but well worth it, after eight months without the use of my oven.